Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Jigsaw: Motor-Rocked C-Frame on a Leaf Spring (Heese, US 2,692,622, 1954)
Woody

Створено

Woody

3. листопад 2026NO
8
0
0
0
0

Jigsaw: Motor-Rocked C-Frame on a Leaf Spring (Heese, US 2,692,622, 1954)

A small electric jig saw for curved cuts. A long U-shaped frame holds a fine blade stretched between its two arms. The frame's back end hangs on an L-shaped leaf spring, and an eccentric on a motor shaft rocks its lower arm up and down, so the blade saws through a slot in the table while the spring flexes. A wing nut tensions the blade; sawdust falls into a box below. Result: a compact motor-driven jig (scroll) saw. Source: G. O. Heese, US 2,692,622 (1954). Unknown: materials, sizes, the motor and the stroke. Picture: the patent drawing.
Середній
Unknown

Інструкції

1

Build the base and table

Make a long flat base, wider at the front. Fasten a long upright support along it, its back end a separate upright strip. Across the wide front stand two walls with matching upright guide slots, carrying a level table that overhangs to the front with a slot for the blade. Under the overhang set a removable open box for sawdust. Not given: materials, sizes.

Матеріали для цього кроку:

Невідомий матеріалНевідомий матеріал1 base, support, walls, table, box
Набір шестигранних болтівНабір шестигранних болтів1 fasteners

Необхідні інструменти ({count})

Ножівка по металуНожівка по металу
Ручний дрильРучний дриль
Невідомі розміриНевідомі розміри
2

Make the C-frame and spring hinge

Make a U-shaped blade frame: an upper arm, a lower arm, and a back piece made in one with the lower arm and bolted to the upper. Fix the upright part of an L-shaped leaf spring to the support's back strip; its flat part goes into a slot in the frame's back piece and is held by the same bolt. The frame can now swing up and down on the spring, its lower arm running in the walls' guide slots under the table.

Матеріали для цього кроку:

Невідомий металНевідомий метал1 frame arms and back
Листова ресораЛистова ресора1 штука
Набір шестигранних болтівНабір шестигранних болтів1 штука
Шестигранна гайкаШестигранна гайка1 штука

Необхідні інструменти ({count})

Розвідний ключРозвідний ключ
3

Fit the motor and eccentric

Fix an electric motor on the wide front of the base with its shaft running across under the frame's lower arm. Put two bolts down through the lower arm, one each side of the shaft; on them hang a lower strip resting on nuts and an upper strip under the arm, with a coil spring on each bolt pushing the strips apart. Fix an eccentric on the motor shaft between the two strips: as it turns it rocks the frame. Not given: the motor, the throw.

Матеріали для цього кроку:

ЕлектродвигунЕлектродвигун1 штука
Ексцентрикова втулкаЕксцентрикова втулка1 eccentric
Невідомий металНевідомий метал1 two strips
Набір шестигранних болтівНабір шестигранних болтів1 two bolts
Шестигранна гайкаШестигранна гайка2 штук
Набір пружин стискуНабір пружин стиску1 two coil springs

Необхідні інструменти ({count})

Розвідний ключРозвідний ключ
4

Fit the blade clamps and use it

On the lower arm fix a strip with a forked end that hooks under the blade's lower pin. On the upper arm fit a bracket with a cross pin; an arm rocks on it, its forked front end over the blade's upper pin, its back end pulled down by a bolt with a wing nut. Add forked guide strips above and below the table. To fit a blade, loosen the wing nut, hook both pins and tighten the nut to stretch the blade straight. Switch on and feed the work across the table. Ours: a pinned coping-saw blade.

Матеріали для цього кроку:

Невідомий металНевідомий метал1 clamp strips, bracket, arm, guides
Гайка-баранецьГайка-баранець1 штука
Набір шестигранних болтівНабір шестигранних болтів1 штука
Пилка для лобзикової пилкиПилка для лобзикової пилки1 pinned blade

Необхідні інструменти ({count})

Розвідний ключРозвідний ключ

Матеріали

10

Необхідні інструменти

4

За цим кресленням виготовляють

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...