Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Water-Chamber Box Churn: A Turning Box With a Dash-Frame You Lower to Free the Butter
Buttercup

Створено

Buttercup

10. листопад 2026IE
11
0
0
0
0

Water-Chamber Box Churn: A Turning Box With a Dash-Frame You Lower to Free the Butter

S. S. Langdon of Cleveland, Ohio, received US 25,126, dated 16 August 1859, for a rotary churn shaped like a common box. It turns on two journals in a frame. Inside, two zinc partitions set into saw kerfs make a cream chamber in the middle and two water chambers at the ends, for warm or cold water to temper the cream. A dash-frame of bars, held by a spring, sits midway while churning and is lowered to the bottom so the butter comes out without being pulled through it. Langdon gives no sizes; every size here is ours, and stainless steel stands in for his zinc.
Середній
About 2 days

Інструкції

1

How much cream, how much water

Завантаження блокнота Jupyter…
2

A box churn tempered with water, before it

Langdon knew a box churn with water chambers had been used without a dasher. He added the dash-frame.
3

Read US 25,126

"When churning, I place the dash-frame about midway from the top to the bottom of the churn, as shown in Fig. 2. When the operation of churning is completed the dash-frame may be lowered to the bottom of the churn in order to remove the butter without interfering with the latter or causing it to adhere to the dasher".
4

Box and kerfs

From 19 mm hardwood cut a bottom 440 x 278 mm, two sides 440 x 240 mm and two ends 240 x 240 mm. Saw a kerf 1 mm wide and 6 mm deep across each side and the bottom, 150.4 mm either side of the middle, for the partitions. Glue and screw the ends between the sides and the box onto the bottom, square.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини2 штук
Столярний клейСтолярний клей1 штука
Шурупи по деревуШурупи по дереву24 штук

Необхідні інструменти ({count})

Циркулярний верстатЦиркулярний верстат
Ручна пилкаРучна пилка
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Струбцина з напрямноюСтрубцина з напрямною
Столярний косинецьСтолярний косинець
РулеткаРулетка
5

Partitions F and the water chambers E

Cut two stainless sheet plates 251 x 245 mm, 0.8 mm thick, and slide them down the kerfs: each closes off a water chamber 50 mm long at an end. Drill a 17 mm hole low in each end board and one in the bottom of the cream chamber, for the plugs. Fill the box with water overnight so the wood swells tight round the plates; check that each water chamber holds water without filling the cream chamber, then empty it.

Матеріали для цього кроку:

Лист нержавкої сталіЛист нержавкої сталі1 штука
Філамент PETGФіламент PETG1 штука

Необхідні інструменти ({count})

Ножиці по металуНожиці по металу
Напилки (ручний напилок)Напилки (ручний напилок)
Акумуляторний дрильАкумуляторний дриль
Набір перових сверделНабір перових свердел
ВодаВода
3D-принтер FDM3D-принтер FDM
6

Print the plugs L

A tapered plug 18 mm at the head, 25 mm long. Print three. PETG, 0.2 mm layers, 100 % infill.
Файл дизайнуSTLCC0 - Free
7

Dash-frame K and spring K'

Cut two hardwood rails 296 x 44 x 20 mm and seven bars 20 x 20 x 196 mm. Fix the bars between the rails set diamond-wise, one corner up, as Fig. 2 draws, 37 mm apart, glued and screwed through the rails. Rivet or screw a bowed strip of stainless spring steel, 256 mm long, along the outside of one rail so it presses on the side and holds the frame wherever you set it.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини1 штука
Холоднокатана стрічка з нержавної сталі (420)Холоднокатана стрічка з нержавної сталі (420)1 штука
Столярний клейСтолярний клей1 штука
Шурупи по деревуШурупи по дереву14 штук

Необхідні інструменти ({count})

Циркулярний верстатЦиркулярний верстат
Ручна пилкаРучна пилка
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Ножиці по металуНожиці по металу
8

Cover G, journals B, frame A and crank C

Cut the cover from 12 mm plywood to the box's outside size. Set four 6 mm bolts head down in the sides' top edges, 75 mm either side of the middle, through matching holes in the cover, with wing nuts on top. Glue and screw a hardwood block 80 x 80 x 40 mm to the middle of each end, bore it 20 mm, drive in a 20 mm steel stub and pin it with a bolt across. Build a pine frame on four posts with open slots in its top rails for the stubs, and a crank with a turned handle on one stub outside the frame.

Матеріали для цього кроку:

Лист фанериЛист фанери1 штука
Набір шестигранних болтівНабір шестигранних болтів6 штук
Гайка-баранецьГайка-баранець4 штук
Плоска шайбаПлоска шайба4 штук
Самоконтрувальна гайка з нейлоновим кільцемСамоконтрувальна гайка з нейлоновим кільцем2 штук
Дошка з твердої деревиниДошка з твердої деревини1 штука
Сталевий пруток-заготовкаСталевий пруток-заготовка1 штука
Хвойний брус 70x70 ммХвойний брус 70x70 мм2 штук
Соснова дошкаСоснова дошка1 штука
Столярний клейСтолярний клей1 штука
Шурупи по деревуШурупи по дереву24 штук

Необхідні інструменти ({count})

Ручна пилкаРучна пилка
Акумуляторний дрильАкумуляторний дриль
Набір перових сверделНабір перових свердел
Набір сверделНабір свердел
Ножівка по металуНожівка по металу
Розвідний ключРозвідний ключ
Столярний косинецьСтолярний косинець
РулеткаРулетка
9

The build in 3D

FreeCAD model of this build, cover and one side cut away: the cream chamber between the stainless partitions, the water chambers at the ends with their plugs, the dash-frame of diamond-set bars midway, the journal blocks, the frame and the crank. The box was turned through 16 angles in the frame.
Файл дизайнуBLENDCC0 - Free
10

Temper and churn

Fill both water chambers with warm or cold water as needed, checked with the thermometer, and plug them. Set the dash-frame midway, pour in about 5 litres of heavy cream, bolt the cover on and turn the crank steadily, timing it. When the butter comes, take the cover off, push the dash-frame down to the bottom, lift the butter out over it and drain the buttermilk at the bottom plug. Wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.

Матеріали для цього кроку:

Жирні вершкиЖирні вершки5 l
Крупна морська сільКрупна морська сіль1 штука
ВодаВода1 штука

Необхідні інструменти ({count})

Термометр зі щупом, що лишається в стравіТермометр зі щупом, що лишається в страві
ЕлектрочайникЕлектрочайник
СекундомірСекундомір
Цифрові кухонні вагиЦифрові кухонні ваги
Велика миска з нержавкої сталіВелика миска з нержавкої сталі
11

Troubleshooting

Water-chamber churn troubleshooting.

Flow

Loading...
12

History and honest limits

**S. S. Langdon** of Cleveland, Ohio, US 25,126, 16 August 1859, "Churn". He claimed his construction and arrangement of rotary churns with the dash-frame K and the water chambers E. He gives no sizes, so every size here is ours. Stainless steel replaces his sheet zinc because the cream and buttermilk touch the partitions; four wing-nut bolts are his "thumb screws placed on the edge of the cover"; the spring strip and the journal blocks are our versions of his spring K' and journals B.

Матеріали

17

Необхідні інструменти

19

Файли дизайну

2

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...