Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО

Leave-In Probe Thermometer: Stainless Probe on a Flexible Lead to a Programmable Timer (Chapman, US 6,568,848, 2003)
A meat thermometer you leave in the roast. A pointed stainless steel probe stays in the meat. A flexible lead runs out of the oven to a battery timer unit with a display, keys and a beeper. You pick the meat and how well done you want it; the unit shows the temperature and the time left, and beeps when it is done.
Result: continuous reading of the inside of the meat without opening the oven.
Source: P. A. Chapman and C.-A. Chang (Maverick Industries), US 6,568,848 (2003). The patent's main form sends the readings by radio; it also states this wired form. Unknown: the sensor, the circuit, the target temperatures and the materials. Picture: the patent drawing.
Середній
Unknown
Інструкції
1
1
Make the probe
Make the probe
Make the probe of a rigid material such as stainless steel. It has a pointed end that goes into the meat, a straight section from the point, then a curved section to the other end. The temperature sensor sits inside. Not given: the type of sensor, sizes.
Матеріали для цього кроку:
Трубка термометра із загостреною пробкою1 stainless steel
Датчик температури1 штукаНеобхідні інструменти ({count})
Невідомі розміри
Паяльник2
2
Fit the flexible lead and plug
Fit the flexible lead and plug
Join a flexible lead to the curved end of the probe, so the probe can lie at any angle to the unit. Put a plug with a male end on the other end of the lead. Not given: the lead material, the plug type, the length.
Матеріали для цього кроку:
Багатожильний кабель1 flexible lead
Невідомий роз’єм1 plug
Дріт припою1 as neededНеобхідні інструменти ({count})
Паяльник
Невідомі розміри3
3
Build the timer unit
Build the timer unit
In a hand-held case, fit a microprocessor that runs the cooking programs, a liquid crystal display, a beeper and batteries. Fit nine keys: clock or timer, probe A or B, meat type, doneness, two to set and change the final temperature, hours, minutes, and start/stop. Add a jack for each probe, a stand to set it upright and a clip for a belt or pocket. Not given: the circuit, the program, the case material.
Матеріали для цього кроку:
Друкована плата1 штука
Інтегральна мікросхема1 microprocessor
Сегментний РК-індикатор1 штука
Кнопка9 keys
П'єзовипромінювач1 штука
Невідомий роз’єм2 probe jacks
Акумулятор1 as needed
Невідомий матеріал1 case, stand, clip
Дріт припою1 as neededНеобхідні інструменти ({count})
Паяльник
Набір викруток4
4
Roast with it
Roast with it
Plug the probe into the timer unit. Pick the meat (beef, veal, lamb, pork, chicken, turkey) and the doneness (rare, medium rare, medium, well-done); the patent cooks to USDA guidelines. Push the probe into the meat, put it in the oven and lead the cable out to the unit, then press start. The display shows the meat, the doneness, the temperature (°F or °C) and the time left, and the beeper sounds at the right moments. A second probe watches a second piece. Not given: the temperature for each doneness.
Необхідні інструменти ({count})
ДуховкаМатеріали
12- 1 stainless steelЗаповнювач
- Заповнювач
- 1 flexible leadЗаповнювач
- 2 probe jacksЗаповнювач
- 2 as neededЗаповнювач
- 1 штукаЗаповнювач
- 1 microprocessorЗаповнювач
- 1 штукаЗаповнювач
- Заповнювач
- 1 штукаЗаповнювач
- 1 as neededЗаповнювач
- 1 case, stand, clipЗаповнювач
Матеріали з пов'язаних креслень
За цим кресленням виготовляють
Пов'язані креслення
Ці креслення діляться знаннями — техніки, матеріали або принципи
CC0 Суспільне надбання
Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.
Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.




