Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Front Horseshoe Forged in Two Heats: Bend, Bevel, Concave, Fuller and Punch (Lungwitz and Adams, Text-Book of Horseshoeing, 1913)
Forge

Створено

Forge

13. листопад 2026NO
3
0
0
0
0

Front Horseshoe Forged in Two Heats: Bend, Bevel, Concave, Fuller and Punch (Lungwitz and Adams, Text-Book of Horseshoeing, 1913)

A flat front horseshoe made from one iron bar, as taught at the Dresden shoeing school: bend each branch over the anvil, bevel and flatten it, concave the hoof side, fuller the crease, and stamp and pritchel the nail holes. From Lungwitz and Adams, A Text-Book of Horseshoeing (11th edition, 1913). "Any ordinary shoe can and should be completed in the rough in two heats." Fitting and nailing the shoe to the horse are not covered here.
Середній
8-15 minutes a pair, once practised

Інструкції

1

Bar length and sizes

Завантаження блокнота Jupyter…
2

Read Lungwitz and Adams

"A shoe should be made thoughtfully, but yet quickly enough to make the most of the heat."
3

Measure the hoof

Measure the length of the hoof from the point of the toe to the buttress, and its greatest width. Added together they give the length of the bar. To keep the exact outline, set the hoof on stiff paper and trace round the wall with a pencil.

Необхідні інструменти ({count})

РулеткаРулетка
ОлівецьОлівець
Аркуші щільного паперуАркуші щільного паперу
4

Cut the bar

Choose good, tough iron, of a width and thickness that needs the least working. Cut the bar to the length you measured; a bar shoe or a shoe with heel calks needs a longer bar.

Матеріали для цього кроку:

Пруток кованого залізаПруток кованого заліза1 штука

Необхідні інструменти ({count})

Кувальне горноКувальне горно
Підсічка ковадлаПідсічка ковадла
Ковальські кліщіКовальські кліщі
Молоток для заокругленняМолоток для заокруглення
5

Bend the outer branch

Heat the bar white-hot just beyond its middle. Lay the head of the sledge across one end of the anvil face, hold the cold end of the bar on it with the hot end on the face, and bend the bar into a half-circle with the round head of the turning hammer. Make the outer branch first, and the right shoe first in a pair. Draw out the end to width and thickness with the sledge.

Необхідні інструменти ({count})

Кувальне горноКувальне горно
Шперак (ковадельце з дзьобом)Шперак (ковадельце з дзьобом)
Вантажні саниВантажні сани
Молоток для заокругленняМолоток для заокруглення
Ковальські кліщіКовальські кліщі
6

Bevel and flatten

Lay the bent branch obliquely across the heel of the horn, turn it to the right onto an edge, and bevel it diamond-shaped from toe to end. Flatten it on the face: bending stretched and thinned the outer edge and thickened the inner one, so leave the inner edge a trifle thinner. Go over it lightly on the horn with the flat face of the hammer to shape it.

Необхідні інструменти ({count})

Шперак (ковадельце з дзьобом)Шперак (ковадельце з дзьобом)
Молоток для заокругленняМолоток для заокруглення
Ковальські кліщіКовальські кліщі
7

Concave and fuller

Concave (seat) the hoof side, ending about 3/4 in from the end of the branch, or leave it flat for an arched sole. Turn the branch and fuller it: set the fuller about 1/12 in from the edge on small shoes, more on large ones, and lead it from the end of the branch to the toe, twice, to about two-thirds of the thickness.

Необхідні інструменти ({count})

Шперак (ковадельце з дзьобом)Шперак (ковадельце з дзьобом)
Вантажні саниВантажні сани
Фулер (прутик для канавок)Фулер (прутик для канавок)
Молоток для заокругленняМолоток для заокруглення
Ковальські кліщіКовальські кліщі
8

Stamp and pritchel the nail holes

Stamp the nail holes in the crease and punch them through with the pritchel. Six are enough for a medium shoe, all in the front half and none at the toe. Their distance from the outer edge equals the thickness of the wall there; incline the toe holes a little inward and punch the quarter holes straight. Each hole tapers from the ground side to the hoof side.

Необхідні інструменти ({count})

Шперак (ковадельце з дзьобом)Шперак (ковадельце з дзьобом)
Гарячий пробійникГарячий пробійник
Пробійник для цвяхових отворівПробійник для цвяхових отворів
Молоток для заокругленняМолоток для заокруглення
Ковальські кліщіКовальські кліщі
9

Finish the branch, then the other

Run over the surfaces, go over the outer edge on the horn, and hammer the bearing surface smooth and level. Make the inner branch the same way, turned to the left and fullered from toe to heel. The finished front shoe is round at the toe and about 7/16 in thick; a hind shoe is bent more pointed at the toe and needs no concaving, only the inner edge rounded.

Необхідні інструменти ({count})

Кувальне горноКувальне горно
Шперак (ковадельце з дзьобом)Шперак (ковадельце з дзьобом)
Молоток для заокругленняМолоток для заокруглення
Фулер (прутик для канавок)Фулер (прутик для канавок)
Гарячий пробійникГарячий пробійник
Пробійник для цвяхових отворівПробійник для цвяхових отворів
Ковальські кліщіКовальські кліщі
10

Troubleshooting

Horseshoe troubleshooting.

Flow

Loading...
11

History and honest limits

From **A Text-Book of Horseshoeing, for Horseshoers and Veterinarians**, by A. Lungwitz (Dresden shoeing school) and John W. Adams (University of Pennsylvania), 11th edition, J. B. Lippincott, 1913 (Project Gutenberg 66786), chapter III F, "Making Shoes"; wall thicknesses after Mayer. Not covered: trimming, fitting and nailing the shoe to the hoof, clips, calks and special shoes. The book names no forge fuel. The metric figures are ours.

Матеріали

1

Необхідні інструменти

12

За цим кресленням виготовляють

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...