Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО

Mechanical Kitchen Scale: Sheet-Metal Case, Guided Plate and Two Springs to a Dial (Hansen, 1939)
The everyday kitchen spring scale, built almost entirely from sheet metal. The platform hangs from a plate that two pivoted links keep moving straight up and down, the way Roberval's frame keeps a pan level. Two springs carry the load, and a rack turns the numbered dial behind a small window.
Result: a household scale that reads the true weight even when the food is put on one edge of the platform, because the dial is driven from the point midway between the two springs. It goes together from three units: case, weighing works and platform.
Source: M. H. Hansen (Hanson Scale Co.), US Patent 2,145,480 (1939). Unknown: the sheet metal and its sizes, the springs, the capacity and how the dial is marked. Picture: patent drawing.
Просунутий
3 days
Інструкції
1
1
Make the case and fit the dial
Make the case and fit the dial
Bend sheet metal into a U: a front wall and two side walls, the lower edges flared outward to stand steady, open at the top and back, with inturned flanges on the back edges. Cut a sector-shaped window in the front and glaze it. Fix a bracket across the side walls, and run the dial shaft from the front wall to the bracket. On the shaft goes the round dial, numbered on its face, and a pinion behind it. Fit a fixed pointer at the window. Not given: the metal, gauge and sizes, and how the dial is numbered.
Матеріали для цього кроку:
Невідомий метал1 аркуш
Віконне скло1 window
Циферблат і стрілка ваг1 штука
Шестірня-трибка1 штукаНеобхідні інструменти ({count})
Ножиці по металу
Набір пасатижів
Невідомі розміри2
2
Build the guided plate on two springs
Build the guided plate on two springs
On a flat rear plate, pin two horizontal links: a lower rectangular one and an upper triangular one. Pin their front ends to an upright plate, which can now only move straight up and down. Hang the upright plate from two tension springs at its lower corners. Hook their tops to the arms of a U-shaped bracket pivoted on the rear plate. A bolt through the rear plate, with a compression spring and a nut, swings the bracket to set the zero.
Матеріали для цього кроку:
Невідомий метал1 аркуш
Шпильки1 набір
Пружина розтягу2 штук
Набір пружин стиску1 one spring
Машинні гвинти1 zero bolt
Шестигранна гайка1 штукаНеобхідні інструменти ({count})
Ножиці по металу
Набір пасатижів
Невідомі розміри3
3
Drive the dial from the middle
Drive the dial from the middle
Pivot an arm on the rear plate and join it by a short link to the upright plate at the pin midway between the two springs. If food sits off-centre, the platform tips and one spring stretches more, but the middle point moves by the average, so the arm gives the true weight. Pass the arm through a hole in the upright plate. Pin it to a curved rack cut in one piece with its extension, so a loose arm cannot skew the rack. The rack will mesh with the dial pinion.
Матеріали для цього кроку:
Невідомий метал1 аркуш
Шпильки1 набірНеобхідні інструменти ({count})
Ножиці по металу
Набір пасатижів4
4
Make the platform
Make the platform
Cut a rectangular sheet-metal platform with a flange turned down all round. Make the flange clear the case walls, so a tipped platform cannot rub and dirt stays out. Rivet a U-shaped bracket under it. Its two arms end in slotted hooks that drop into openings in the upright plate, held by its flanges so the platform cannot tilt on it.
Матеріали для цього кроку:
Невідомий метал1 аркуш
Сталеві заклепки1 a fewНеобхідні інструменти ({count})
Ножиці по металу
Набір пасатижів5
5
Assemble and set the zero
Assemble and set the zero
Lower the weighing works into the case through the open top: the rack drops into mesh with the dial pinion. Screw the rear plate to the case flanges. Hook the platform on. With the platform empty, turn the zero nut until the zero on the dial stands at the pointer. Turn it again later if the springs stretch. Ours: check the reading with a known weight.
Матеріали для цього кроку:
Машинні гвинти1 rear plate screwsНеобхідні інструменти ({count})
Набір викруток
ВантажМатеріали
10- 1 аркушЗаповнювач
- 1 windowЗаповнювач
- 1 штукаЗаповнювач
- 1 штукаЗаповнювач
- 2 наборівЗаповнювач
- 2 штукЗаповнювач
- 1 one springЗаповнювач
- 1 rear plate screwsЗаповнювач
- 1 штукаЗаповнювач
- 1 a fewЗаповнювач
Матеріали з пов'язаних креслень
За цим кресленням виготовляють
Пов'язані креслення
Ці креслення діляться знаннями — техніки, матеріали або принципи
CC0 Суспільне надбання
Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.
Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.




