Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Shaft Collar Without a Set Screw: Split Halves With a Tapered Thread, Clamped by a Nut (Melius, 1904)
Forge

Створено

Forge

13. листопад 2026NO
5
0
0
0
0

Shaft Collar Without a Set Screw: Split Halves With a Tapered Thread, Clamped by a Nut (Melius, 1904)

Charles H. Melius of Gloversville, New York, received US 758,549, dated 26 April 1904, for a shaft collar that holds "without the use of set-screws". The collar is cut lengthwise in two halves that go round the shaft from the side. Each half has part of a flange and part of a tapered, threaded body. A nut screwed onto the taper squeezes the halves onto the shaft. It grips anywhere along the shaft and does not mark it. We build the form in his Fig. 1, with a solid nut that goes on over the shaft's end before the halves. The thread is a standard 3/4 inch taper pipe thread. The patent gives no sizes; every size here is ours.
Середній
About 4 hours

Інструкції

1

How hard the nut squeezes the halves

Завантаження блокнота Jupyter…
2

Read US 758,549

"Ordinary shaft-collars are generally in the form of a continuous ring, and it is necessary to slip the same over the ends of the shaft, and the collar is secured in place by transverse set-screws." "The halves of the part A when arranged upon the shaft do not come in close contact with one another, but are a slight distance apart, so that when the nut C is threaded upon the portion B the halves of the part A will be drawn together and tightly clamped upon the shaft."
3

Turn the male part A

Grip 36 mm A/F hex bar in the 3-jaw chuck with 35 mm sticking out. Face the end. Turn the body round to 26.7 mm for 20 mm from the end, leaving the hex as the flange, and chamfer the end 1 mm. Centre-drill, drill through 15 mm and ream 16 mm, or bore to 16 mm; check that the shaft slides through. Part off 28 mm from the end, so the flange is 8 mm thick.

Матеріали для цього кроку:

Шестигранний пруток із м'якої сталіШестигранний пруток із м'якої сталі1 штука
Мастильно-охолоджувальна оливаМастильно-охолоджувальна олива1 штука

Необхідні інструменти ({count})

Токарний верстат по металуТокарний верстат по металу
Трикулачковий токарний патронТрикулачковий токарний патрон
Токарний різецьТокарний різець
Набір центрувальних сверделНабір центрувальних свердел
Набір сверделНабір свердел
РозверткаРозвертка
Розточна оправкаРозточна оправка
Відрізний різецьВідрізний різець
Цифровий штангенциркуль 6 дюймівЦифровий штангенциркуль 6 дюймів
Захисні окуляриЗахисні окуляри
4

Cut the tapered thread B

Hold the part by its hex flange in the vice, in soft jaws. Start the 3/4 inch taper pipe die square on the chamfer, in its die stock, and cut the thread up to the flange with cutting oil, backing off every half turn to break the chips. The die cuts the 1 in 16 taper itself: the thread is biggest at the flange.

Матеріали для цього кроку:

Мастильно-охолоджувальна оливаМастильно-охолоджувальна олива1 штука

Необхідні інструменти ({count})

Слюсарні лещатаСлюсарні лещата
М'які губки для лещатМ'які губки для лещат
Taper Pipe DieTaper Pipe Die
ПлашкотримачПлашкотримач
5

Make the nut C

From the same hex bar, face, centre-drill and drill through in steps up to 23.4 mm (59/64 inch), then part off 14 mm long. Hold it in the vice and run the 3/4 inch taper pipe tap in from one face with cutting oil until part A screws in by hand about half its thread length. Mark the face you tapped from: the larger end of the thread, it goes towards the flange. Deburr both faces.

Матеріали для цього кроку:

Шестигранний пруток із м'якої сталіШестигранний пруток із м'якої сталі1 штука
Мастильно-охолоджувальна оливаМастильно-охолоджувальна олива1 штука

Необхідні інструменти ({count})

Токарний верстат по металуТокарний верстат по металу
Трикулачковий токарний патронТрикулачковий токарний патрон
Токарний різецьТокарний різець
Набір центрувальних сверделНабір центрувальних свердел
Набір сверделНабір свердел
Відрізний різецьВідрізний різець
Taper Pipe TapTaper Pipe Tap
Коловорот для мітчиківКоловорот для мітчиків
Слюсарні лещатаСлюсарні лещата
Знімач задирокЗнімач задирок
Цифровий штангенциркуль 6 дюймівЦифровий штангенциркуль 6 дюймів
6

Split part A in two halves

Blue the flange face and scribe a line across it through the centre, from corner to corner of the hex. Hold the part in soft jaws with the line upright and saw straight down the line, through flange and body, with a fine hacksaw blade. File the saw marks off the cut faces but take no more: the 1 mm gap left between the halves is what lets the nut squeeze them onto the shaft. Deburr the bore and the thread ends.

Необхідні інструменти ({count})

Синя контрольна фарбаСиня контрольна фарба
РисувалкаРисувалка
Слюсарні лещатаСлюсарні лещата
М'які губки для лещатМ'які губки для лещат
Ножівка по металуНожівка по металу
Набір напилківНабір напилків
Знімач задирокЗнімач задирок
7

The collar in 3D

FreeCAD model, our sizes: the two halves of part A, each with half the hex flange and half the tapered body, 1 mm apart on a 16 mm shaft, and the hex nut C on the taper. The thread itself is not modelled, only the cone.
Файл дизайнуSTLCC0 - Free
8

Fit it on the shaft

Slide the nut onto the shaft from its end, marked face first. Put the two halves round the shaft where the collar is wanted, flange towards the face it must bear on, and hold them together. Screw the nut onto the taper by hand, then hold the flange with one spanner and tighten the nut with the other until the halves grip. Try to slide and turn the collar on the shaft; it must not move. To move it, slacken the nut, slide the halves, and tighten again.

Необхідні інструменти ({count})

Розвідний ключРозвідний ключ
9

Troubleshooting

Melius collar troubleshooting.

Flow

Loading...
10

History and honest limits

**Charles H. Melius** of Gloversville, Fulton County, New York, US 758,549, dated 26 April 1904, filed 2 May 1903. He claimed "a shaft-collar consisting of two longitudinally-divided parts adapted to fit around a shaft, a tapered threaded portion formed on one of the parts and an internally-threaded convex wall formed on the other part", the nut's sections joined by tongue and mortise and a pin. His Figs. 3 and 4 show that halved nut, which goes on without reaching the shaft's end; we build Fig. 1's solid nut. His nut thread is "curved" so its threaded portion is convex; ours is the straight taper of a standard pipe thread. He says the flange may be polygonal for a wrench or have holes for a spanner; ours is hex. The patent gives no sizes; every size here is ours.

Матеріали

2

Необхідні інструменти

22

Файли дизайну

1

За цим кресленням виготовляють

Пов'язані креслення

Ці креслення діляться знаннями — техніки, матеріали або принципи

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...