Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Hung-Dasher Churn: The Dasher Hangs in a Long Hinged Journal Box Above the Lid, No Step in the Tub
Buttercup

Створено

Buttercup

11. листопад 2026IE
4
0
0
0
0

Hung-Dasher Churn: The Dasher Hangs in a Long Hinged Journal Box Above the Lid, No Step in the Tub

Jehu Mitchell of Aleppo township, Pennsylvania, received US 27,927, dated 17 April 1860, for a churn. The dasher hangs from above in a long journal box on a standard fixed to the lid, with no step or metal bearing in the tub, whose "oxidation ... imparts a bad flavor to the butter". One half of the box is a cap hinged at one side: lift out half the lid, unhook the cap and the dasher comes out with the gearing left in place. The patent gives no sizes; every size here is ours.
Середній
About 2 days, plus printing

Інструкції

1

Held from above

Завантаження блокнота Jupyter…
2

A crank-turned upright dasher, one week before

Lynch's shaft stands in a step on the bottom. Mitchell hangs his from above, with nothing in the tub.
3

Read US 27,927

"Suspending the dasher within an elongated hinged journal box in the manner described, combined the following advantages. A rigid bearing is afforded to the dasher so as to prevent any tremulous motion, without the necessity of any metallic step or bearing within the churn, the oxidation of which imparts a bad flavor to the butter."
4

Print the driving wheel E

Crown wheel, 36 teeth on its face, module 2, with a hub; bored 12.4 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Файл дизайнуSTLCC0 - Free
5

Print the pinion M

Spur pinion, 12 teeth, module 2, with a hub; bored 12.4 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Файл дизайнуSTLCC0 - Free
6

Lid B and C, brakes O

Cut a hardwood lid 15 mm thick to sit on the bucket's rim and saw it in two across the middle: part C carries the standard, part B lifts out. Cut a 28 mm half-hole in the middle of the cut edge for the shaft and a 30 mm hole in B to look in. Screw three hardwood brakes O, 30 mm deep and 245 tall, to the bucket's side a third of a turn apart, and seal the screw holes outside with silicone.

Матеріали для цього кроку:

Відро на 20 літрівВідро на 20 літрів1 штука
Дошка з твердої деревиниДошка з твердої деревини2 штук
Шурупи по деревуШурупи по дереву6 штук
Силіконовий герметикСиліконовий герметик1 штука

Необхідні інструменти ({count})

ЕлектролобзикЕлектролобзик
Циркулярний верстатЦиркулярний верстат
Набір перових сверделНабір перових свердел
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Набір викрутокНабір викруток
РулеткаРулетка
7

Standard D, journal box and cap G

Glue up a hardwood standard 60 mm wide and 66 deep, 111 mm tall above the lid, with its back 22 mm rising to 217 mm and bored 12.6 mm across near the top for the wheel's axle. Mortise it into lid part C behind the shaft's hole. Cut a cap G 60 x 30 mm, 111 tall, and bore a 25.2 mm hole down the joint between standard and cap, half in each. Hang the cap on a butt hinge at one side and fit a hook H and eye I on the other.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини1 штука
Столярний клейСтолярний клей1 штука
Меблева карткова завісаМеблева карткова завіса1 штука
Гачок і петляГачок і петля1 штука
Шурупи по деревуШурупи по дереву4 штук

Необхідні інструменти ({count})

Циркулярний верстатЦиркулярний верстат
Набір стамесок по деревуНабір стамесок по дереву
Струбцина з напрямноюСтрубцина з напрямною
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Набір перових сверделНабір перових свердел
Набір викрутокНабір викруток
8

Dasher J with wings N and collars K and L

Cut a 25 mm hardwood dowel 485 mm long and glue a 12 mm stainless spindle into its top, standing 56 mm out. Glue two hardwood wings 200 x 60 x 20 mm across it, 20 and 140 mm above its foot, each bored with two 24 mm holes. Fit a hardwood collar L 44 mm across just below the lid, and a collar K 40 mm across on the spindle resting on the box's top. Set the shaft in the box, close the cap, and key the pinion M on the spindle above K.

Матеріали для цього кроку:

Шканти з твердої деревиниШканти з твердої деревини2 штук
Дошка з твердої деревиниДошка з твердої деревини1 штука
Пруток із нержавкої сталіПруток із нержавкої сталі1 штука
Столярний клейСтолярний клей1 штука
Брусок твердої деревиниБрусок твердої деревини1 штука
Shaft CollarShaft Collar1 штука
Філамент PETGФіламент PETG1 штука

Необхідні інструменти ({count})

3D-принтер FDM3D-принтер FDM
Циркулярний верстатЦиркулярний верстат
Набір перових сверделНабір перових свердел
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Ножівка по металуНожівка по металу
Напилки (ручний напилок)Напилки (ручний напилок)
Наждачний папірНаждачний папір
9

Driving wheel E and crank

Pass a 12 mm stainless axle through the standard's back, fit the wheel E on it meshing the pinion, and a hardwood crank with a dowel handle on the other end; hold it with a collar and split pin.

Матеріали для цього кроку:

Пруток із нержавкої сталіПруток із нержавкої сталі1 штука
Дошка з твердої деревиниДошка з твердої деревини1 штука
Шканти з твердої деревиниШканти з твердої деревини1 штука
Столярний клейСтолярний клей1 штука
Shaft CollarShaft Collar1 штука
ШплінтШплінт1 штука

Необхідні інструменти ({count})

Ножівка по металуНожівка по металу
Напилки (ручний напилок)Напилки (ручний напилок)
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Слюсарні лещатаСлюсарні лещата
10

The build in 3D

FreeCAD model of this build, the bucket cut open: the dasher J with its two wings hanging from the journal box, the brakes O, the lid, the standard D with its hinged cap G, hook and eye, and the wheel E with pinion M.
Файл дизайнуBLENDCC0 - Free
11

Churn

Pour about 8 litres of heavy cream at about 15 °C, checked with the thermometer, into the bucket, set the lid and dasher in place, and turn the crank steadily, timing it. To look at the butter, lift out lid part B. When the butter comes, lift part B out, unhook the cap and take the dasher out, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

Матеріали для цього кроку:

Жирні вершкиЖирні вершки8 l
Крупна морська сільКрупна морська сіль1 штука
ВодаВода1 штука

Необхідні інструменти ({count})

Термометр зі щупом, що лишається в стравіТермометр зі щупом, що лишається в страві
СекундомірСекундомір
Цифрові кухонні вагиЦифрові кухонні ваги
Велика миска з нержавкої сталіВелика миска з нержавкої сталі
12

Troubleshooting

Hung-dasher churn troubleshooting.

Flow

Loading...
13

History and honest limits

**Jehu Mitchell** of Aleppo township, Greene County, Pennsylvania, US 27,927, 17 April 1860, "Churn". He did not claim a churn without a bottom step nor a hinged bearing alone, but the gearing, standard, hinged cap, dasher and collar together. His journal box runs higher; ours stops below the crown wheel. His wings and brakes are "of common construction"; our two wings and three brakes, and every size, are ours.

Матеріали

16

Необхідні інструменти

18

Файли дизайну

3

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...