Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Oven Thermometer: Door-Mounted Dial with a Curved Bimetal Strip (Whittier, US 1,498,413, 1924)
Penny

Створено

Penny

3. листопад 2026DK
10
0
0
0
0

Oven Thermometer: Door-Mounted Dial with a Curved Bimetal Strip (Whittier, US 1,498,413, 1924)

A dial thermometer that fits in an oven door or wall. Behind an enamelled dial plate, a curved bimetal strip runs from a fixed stud to a little arm on a spindle; as the oven heats, the strip bends, turns the spindle and swings the pointer across the scale on the front. Everything is mounted on the dial plate as one unit and dropped into a shallow stamped case with a glass cap. Result: a compact oven thermometer, easy to calibrate and adjust. Source: H. R. Whittier, US 1,498,413 (1924). Unknown: metals, sizes and the scale unit. Picture: the patent drawing.
Середній
Unknown

Інструкції

1

Make the dial unit

Cut a metal disk for the dial plate, enamel its front and mark the scale (the patent's drawing reads 200 to 500). Thread a sleeve through the plate near one edge and pass a spindle loosely through it, with a pointer fixed on its front end and a short arm on its back end. Set a stud through the plate: in front it stops the pointer, behind it anchors one end of a curved bimetal strip whose other end is pinned to the arm. Not given: metals, sizes, the scale unit.

Матеріали для цього кроку:

Невідомий металНевідомий метал1 dial plate, sleeve, spindle, pointer, arm, stud
Невідомий матеріалНевідомий матеріал1 enamel and scale
Біметалева пластинаБіметалева пластина1 curved strip

Необхідні інструменти ({count})

Набір мітчиків і плашокНабір мітчиків і плашок
КруглогубціКруглогубці
Невідомі розміриНевідомі розміри
2

Make the case

Stamp a shallow case from thin sheet metal, closed at the back, with perforated ears for fixing it in the oven door or wall, and press lugs in from its wall for the dial plate to sit on. Make a cap with a glass to close the open front. Ours: steel sheet and a watch glass.

Матеріали для цього кроку:

Лист маловуглецевої сталіЛист маловуглецевої сталі1 case and cap
Годинникове склоГодинникове скло1 window

Необхідні інструменти ({count})

Ножиці по металуНожиці по металу
Невідомі розміриНевідомі розміри
3

Assemble, calibrate and fit

Calibrate the strip and set the pointer while the unit is out of the case, then drop the dial unit onto the lugs and fit the cap, which holds the plate in place. Fasten the case through its ears in the oven door or wall. As the oven heats, the strip bends and the pointer swings across the scale. Not given: how it is calibrated.

Необхідні інструменти ({count})

ДуховкаДуховка
КруглогубціКруглогубці

Матеріали

5

Необхідні інструменти

5

За цим кресленням виготовляють

Пов'язані креслення

Ці креслення діляться знаннями — техніки, матеріали або принципи

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...