Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Platinum Boat: Cut from Foil and Bent over a Brass Former (Blair, 1888)
Charlie

Створено

Charlie

7. листопад 2026DE
9
0
0
0
0

Platinum Boat: Cut from Foil and Bent over a Brass Former (Blair, 1888)

A small trough of platinum foil that carries a sample into a combustion tube. Andrew Blair (1888): "This boat is made by cutting a piece of platinum-foil in the shape shown in Fig. 65, and bending it up over a brass former into the shape shown in Fig. 64." His pattern is 3.5 long, 1.3 wide at one end and 1.07 at the other, with tabs at each end; the figure does not mark the units. Foil thickness and the former are not given. Source: A. A. Blair, The Chemical Analysis of Iron (1888), p. 129. Picture: Figs. 64-65.
Початківець
Unknown

Інструкції

1

Read Blair

"This boat is made by cutting a piece of platinum-foil in the shape shown in Fig. 65, and bending it up over a brass former into the shape shown in Fig. 64."
2

Cut the blank

Cut platinum foil to the pattern of Fig. 65: 3.5 long between the end tabs, 1.3 wide at one end tapering to 1.07 at the other, with a tab .5 wide at the wide end and .37 wide at the narrow end, each flanked by V-notches. The figure does not mark the units, and the foil thickness, and how the foil is made, are not given (unknown).

Матеріали для цього кроку:

ПлатинаПлатина1 foil

Необхідні інструменти ({count})

Ножиці по металуНожиці по металу
Невідомий спосіб формуванняНевідомий спосіб формування
Невідомі розміриНевідомі розміри
3

Bend it over the former

Bend the blank up over a brass former into the trough of Fig. 64, folding the end tabs up to close the ends. The shape of the former, and how it is made, are not given (ours: brass round bar as its stock).

Необхідні інструменти ({count})

Латунний круглий прутокЛатунний круглий пруток
Невідомі розміриНевідомі розміри
4

Use

Blair opens out the sides to slide in a moist carbonaceous residue, bends them back into shape, dries the boat and contents at 100 °C, and pushes it into the porcelain or platinum tube to burn off the carbon.

Матеріали

1
  • Заповнювач

Необхідні інструменти

4

За цим кресленням виготовляють

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...