МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗЕЛЕНЕ МАЙБУТНЄ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО

Making Clay Beads — Hand-Rolled and Pit-Fired Ornaments
Clay beads are among the oldest decorative objects made by humans — fired clay beads from Dolní Věstonice in the Czech Republic date to approximately 26,000 years ago, making them some of the earliest known ceramics. Unlike shell or bone beads that require drilling through hard material, clay beads are formed soft and pierced with a stick before firing, making them far easier to produce in quantity. Beads served as personal ornament, trade goods, counting tokens, and markers of social status across all prehistoric cultures. The process is simple: prepare clay, roll beads, pierce holes, dry, fire. The key challenge is preventing the beads from cracking during drying and firing — uniform thickness, thorough drying, and slow temperature increase are essential.
Початківець
2-3 hours (plus firing)
Інструкції
1
1
Gather and Clean the Clay
Gather and Clean the Clay
Gather fine-grained clay and remove stones, roots, and debris by hand.
Матеріали для цього кроку:
Raw Clay from Riverbank1 штука2
2
Knead the Clay Thoroughly
Knead the Clay Thoroughly
Knead the clay thoroughly to remove air bubbles — wedging on a flat stone works well.
3
3
Add Temper (Optional)
Add Temper (Optional)
Optionally mix in a small amount of fine sand (10-15%) as temper to reduce cracking.
4
4
Roll the Beads
Roll the Beads
Pinch off a small piece of clay and roll it between your palms into a smooth sphere (8-15mm diameter).
5
5
Pierce the Centre Hole
Pierce the Centre Hole
Pierce the centre of each bead with a thin stick, twig, or bone awl — push through from one side, then ream from both sides.
Необхідні інструменти ({count})
Bone Awl6
6
Size the Hole for Cordage
Size the Hole for Cordage
The hole should be large enough for a cord (2-3mm diameter).
7
7
Leave the Stick in During Drying
Leave the Stick in During Drying
Leave the stick in place while drying to keep the hole open and prevent it from closing.
8
8
Dry Slowly in Shade
Dry Slowly in Shade
Set beads on a dry surface in shade and dry slowly for 2-3 days — fast drying causes cracks.
9
9
Remove the Sticks
Remove the Sticks
Remove the sticks once the clay is leather-hard.
10
10
Add Surface Decoration (Optional)
Add Surface Decoration (Optional)
Optional: press patterns into the bead surface with a pointed stick or stamp with cord impressions before drying.
11
11
Fire in a Pit Kiln
Fire in a Pit Kiln
Fire the beads in a pit kiln: place in the coals, cover with fuel, burn for 2-3 hours at 600-800°C, and allow to cool slowly in the ash.
Матеріали
1- 1 штукаЗаповнювач
Необхідні інструменти
1- Заповнювач
Матеріали з пов'язаних креслень
Пов'язані креслення
Ці креслення діляться знаннями — техніки, матеріали або принципи
CC0 Суспільне надбання
Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.
Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.