МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗЕЛЕНЕ МАЙБУТНЄ
ЗБОРНА ІНЖЕНЕРІЯ
ШКІЛЬНІ ПРОЄКТИ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Building a Reed Bundle Raft — Buoyant Watercraft from Wetland Plants
Woody

Створено

Woody

25. травень 2026NO
13
0
0
1
0

Building a Reed Bundle Raft — Buoyant Watercraft from Wetland Plants

The reed bundle raft is one of the oldest watercraft designs, used by cultures worldwide wherever large reeds or bulrushes grow near water. The totora reed boats of Lake Titicaca, the papyrus boats of ancient Egypt, and the tule balsa rafts of Native California all use the same principle: bundles of dried reeds lashed tightly together contain enough trapped air to support a person's weight. Reeds are naturally buoyant because their stems are filled with a spongy aerenchyma tissue. A well-built reed raft can carry 200-400 kg depending on size. The craft is simple to build, requires no metal tools, and the materials grow abundantly in any wetland. The main limitation is lifespan — waterlogged reeds eventually lose buoyancy after 2-4 weeks of continuous use.
Середній
4-6 hours

Інструкції

1

Harvest Reeds

Harvest large quantities of bulrush, cattail, or tule reeds — each stalk should be 2+ metres long.

Матеріали для цього кроку:

Dried ReedDried Reed100 штук
2

Dry the Reeds

Spread the reeds on dry ground and let them dry for 1-2 weeks until they feel light and stiff.
3

Sort by Length

Sort dried reeds by length into matching groups.
4

Form the First Bundle

Form the first bundle: gather a tight armload of reeds (30-40cm diameter) and bind at 3-4 points along its length with strong cordage.

Матеріали для цього кроку:

CordageCordage5 штук
5

Taper Both Ends

Taper both ends of the bundle by using progressively shorter reeds at the outsides — this creates a pointed bow and stern.
6

Make a Second Bundle

Make a second identical bundle.
7

Lash the Bundles Together

Lash the two bundles side by side with cross-lashings every 30-40cm, pulling the bundles as tight as possible.
8

Check the Width

The raft should be wider than the paddler's hips (80-120cm total width).
9

Optional: Add a Deck Bundle

Optional: add a third smaller bundle on top between the two main bundles to create a raised deck.
10

Prepare a Paddle

Tie a paddle or pole before launching.
11

Test in Shallow Water

Test in shallow water first — the raft should sit with the top surface above waterline with the paddler aboard.
12

Store Out of Water

Keep the raft stored out of water when not in use to extend lifespan.

Матеріали

2

Матеріали з пов'язаних креслень

You can swap these in

Can't get one of the materials? Swap it for an equivalent — these work just as well.

Пов'язані креслення

Ці креслення діляться знаннями — техніки, матеріали або принципи

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...