МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗЕЛЕНЕ МАЙБУТНЄ
ЗБОРНА ІНЖЕНЕРІЯ
SCHOOL PROJECTS
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Building Leonardo da Vinci's Revolving Bridge — The Swing Bridge for a Marching Army
Emma

Створено

Emma

2. липень 2026SE
9
0
0
0
0

Building Leonardo da Vinci's Revolving Bridge — The Swing Bridge for a Marching Army

Around 1487 Leonardo da Vinci designed a bridge that swings. Meant for armies on the move, it pivots on a single point on one bank, sweeps across the river in one rigid span, and drops onto the far side — then swings back in moments to leave the river uncrossable behind. Light enough for a handful of soldiers to work with rope, pulley and counterweight, yet strong enough to carry men and light artillery, it is the same swing-bridge principle used today where a bridge must open for passing boats. This blueprint reconstructs Leonardo's revolving bridge as a working model.
Просунутий
24

Інструкції

1

Understand the design

Leonardo's bridge crosses a river in a single rigid span that pivots horizontally on one bank. An army can swing it out to cross, then swing it back to stop the enemy following — quick to deploy and quick to withdraw, unlike a fixed bridge.
2

Build the span

Build a light but stiff timber truss as long as the crossing. It must be rigid enough to carry marching men and light guns, yet light enough that a small crew can swing it — a classic strength-to-weight problem Leonardo solved with a trussed frame.

Матеріали для цього кроку:

Beech LumberBeech Lumber6 штук

Необхідні інструменти ({count})

Hand SawHand Saw
3

Set the pivot

Anchor a strong vertical pivot pin on the near bank and seat one end of the span on it, so the whole bridge can rotate freely in the horizontal plane about that single point.

Матеріали для цього кроку:

Dowel RodDowel Rod1 штука

Необхідні інструменти ({count})

Hand AugerHand Auger
4

Rig the ropes and counterweight

Run ropes from the free end of the span through pulleys back to a counterweight, so the counterweight balances most of the bridge's weight. Now a few people hauling the ropes can move a very heavy span with ease.

Матеріали для цього кроку:

Binding RopeBinding Rope40 метрів

Необхідні інструменти ({count})

KnifeKnife
5

Fit a roller at the free end

Mount a wheel or roller under the swinging end so that, as the bridge comes across, it rolls smoothly up onto the far bank rather than dragging or dropping short.

Матеріали для цього кроку:

Beech LumberBeech Lumber1 штука

Необхідні інструменти ({count})

Hand AugerHand Auger
6

Swing it across

Haul on the ropes. With the counterweight carrying the load, the span pivots out over the water and lands its rolling end on the opposite bank — a full river crossing thrown down in minutes.
7

Cross and retract

Send the troops over, then swing the bridge straight back to the near bank. In moments the crossing is gone and the river is a barrier again — the tactical point of a bridge that moves.
8

See the engineering

A single pivot, rope-and-pulley mechanical advantage, and a counterweight turn a massive span into something a small crew can swing quickly and safely. The same principle runs every modern swing bridge that opens to let ships pass.

Матеріали

3

Необхідні інструменти

3

You can swap these in

Can't get one of the materials? Swap it for an equivalent — these work just as well.

Пов'язані креслення

Ці креслення діляться знаннями — техніки, матеріали або принципи

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...