Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Ring Stand: a Brass Rod on a Board Foot with Sliding Rings (Faraday, 1830)
Charlie

Створено

Charlie

7. листопад 2026DE
8
0
0
0
0

Ring Stand: a Brass Rod on a Board Foot with Sliding Rings (Faraday, 1830)

A stand that holds flasks and basins at any height over a lamp or furnace. Michael Faraday (1830) describes the retort-stand: an upright brass rod on a heavy foot, with rings of several sizes, each on an arm whose socket slides up and down the rod and is fixed by a screw-nut at the back. Brass feet filled with lead tip over under a heavy vessel, so he makes the foot a stout board about 12 x 6 x 1 inches, the rod fixed 1 1/2 inches from one end, and stands the lamp or furnace on the board under the ring. Source: M. Faraday, Chemical Manipulation (1830), §386, p. 175. Picture: his woodcut.
Початківець
Unknown

Інструкції

1

Read Faraday

"It is much better to make the foot of a piece of stout board, about twelve inches in length, six inches in width, and an inch thick. The upright rod should be fixed about one inch and a half from one end of it, the lamp or furnace should be placed upon it, and the ring of course in a corresponding direction. Such an arrangement is perfectly steady, and cannot be overset by any weight which it is strong enough to bear."
2

Fix the rod in the board

Take a stout board about 12 in. long, 6 in. wide and 1 in. thick. Fix an upright brass rod in it about 1 1/2 in. from one end. Rod size, and how it is fixed, are not given (unknown). Ours: a hardwood board.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини1 фути
Латунний прутокЛатунний пруток1 upright
Невідомий роз’ємНевідомий роз’єм1 штука

Необхідні інструменти ({count})

Невідомі розміриНевідомі розміри
3

Make the rings

Make several rings of different sizes, each fixed to an arm, and each arm to a socket that slides freely up and down the rod. Fit each socket with a screw-nut at the back to tighten it at any height. The metal and sizes are not given (unknown). Ours: wing nuts for the screw-nuts.

Матеріали для цього кроку:

Невідомий металНевідомий метал1 rings, arms, sockets
Гайка-баранецьГайка-баранець1 штука

Необхідні інструменти ({count})

Невідомі розміриНевідомі розміри
4

Use it

Stand the lamp or furnace on the board and turn the ring over it. Slide the ring to the height wanted and tighten the screw. Do not set a hot flask on a cold ring, or a cold, freshly filled flask on a hot ring over the fire: the bottom may come out (Faraday §388).

Матеріали

5

Необхідні інструменти

1

За цим кресленням виготовляють

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...