Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Spiral-Beater Box Churn: Diamond-Holed and Hollow-Ended Beaters Drive the Cream End to End
Buttercup

Створено

Buttercup

9. листопад 2026IE
9
0
0
0
0

Spiral-Beater Box Churn: Diamond-Holed and Hollow-Ended Beaters Drive the Cream End to End

Harry and Royal V. Robie of Eaton, New York, received US 22,090, dated 16 November 1858, for a box churn with beaters set spirally on a level crank shaft. Every other beater has a diamond hole; the rest have a hollow (concave) end. All are narrow where they join the shaft, so the cream passes between them, and they drive it from one end of the box to the other. A chamber under the box, with a hinged door, holds something cold or warm to bring the cream to temperature. This rung builds it with a food-grade container in a pine body and printed beaters.
Середній
About 6 hours, plus printing

Інструкції

1

Beaters, spacing and fill

Завантаження блокнота Jupyter…
2

Pierced dashers, before it

Farrington broke the cream on the holes of swinging dashers. The Robies pierce every other beater on a turning shaft.
3

Read US 22,090

"... the base of said beaters being made small and narrow where they enter the shaft in order to form an opening for the passage of the cream, between each of the beaters, while the holes in each alternate beater form another passage".
4

Print the beater B

Beater B, with the diamond hole. Print four. PETG, 0.2 mm layers, 30 % infill, 4 walls, with supports under the turned blade; wash before first use.
Файл дизайнуSTLCC0 - Free
5

Print the beater C

Beater C, with the hollow end. Print three. PETG, 0.2 mm layers, 30 % infill, 4 walls, with supports under the turned blade; wash before first use.
Файл дизайнуSTLCC0 - Free
6

Print the crank

The crank arm. PETG, 0.2 mm layers, 30 % infill, 4 walls, with supports under the turned blade; wash before first use.
Файл дизайнуSTLCC0 - Free
7

Print the collar

The collar that holds the shaft's far end. PETG, 0.2 mm layers, 30 % infill, 4 walls, with supports under the turned blade; wash before first use.
Файл дизайнуSTLCC0 - Free
8

Body and chamber

Use a food-grade container 400 x 280 mm inside and 250 mm deep, with a rim. From 18 mm pine cut two ends 362 x 750 mm with a 120 mm arch at the foot, two sides 444 x 630 mm, two rails 444 x 40 mm and a shelf 444 x 326 mm. Screw the sides between the ends, the rails inside the sides 3 mm below the top, and the shelf 200 mm up. Cut a 360 x 272 mm opening in the front side above the shelf and hang a 356 x 268 mm pine door in it on two butt hinges along its bottom edge.

Матеріали для цього кроку:

Соснова дошкаСоснова дошка3 штук
Столярний клейСтолярний клей1 штука
Шурупи по деревуШурупи по дереву40 штук
Карткова завісаКарткова завіса2 штук
Шуруп по дереву #8 x 1"Шуруп по дереву #8 x 1"8 штук

Необхідні інструменти ({count})

Ручна пилкаРучна пилка
ЕлектролобзикЕлектролобзик
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
СтрубциниСтрубцини
Наждачний папірНаждачний папір
Набір викрутокНабір викруток
РулеткаРулетка
9

Shaft A and beaters

Hang the container by its rim on the rails. Drill a 17 mm hole through both pine ends and both container ends, 150 mm above the container's inside floor. Cut the stainless tube (16 mm) to 574 mm and push it through. Slide on the seven beaters, B, C, B, C, B, C, B, 50 mm apart from the middle out, each a quarter turn round from the last, all blades turned the same way, and fix each with an M4 screw across hub and shaft. Fit the collar on the far end and the crank on the near end with M4 screws, and glue a 12 mm dowel 114 mm long into the crank as the handle.

Матеріали для цього кроку:

Посудина для зберігання харчової якостіПосудина для зберігання харчової якості1 штука
Філамент PETGФіламент PETG1 штука
Труба з нержавкої сталіТруба з нержавкої сталі1 штука
Машинні гвинтиМашинні гвинти9 штук
Самоконтрувальна гайка з нейлоновим кільцемСамоконтрувальна гайка з нейлоновим кільцем9 штук
Шканти з твердої деревиниШканти з твердої деревини1 штука
Столярний клейСтолярний клей1 штука

Необхідні інструменти ({count})

3D-принтер FDM3D-принтер FDM
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
ТруборізТруборіз
Напилки (ручний напилок)Напилки (ручний напилок)
Набір викрутокНабір викруток
Розвідний ключРозвідний ключ
10

The build in 3D

FreeCAD model of this build: the pine body with its arched ends, the chamber door, the container on its rails, the shaft with seven spiral beaters, the collar and the crank.
Файл дизайнуBLENDCC0 - Free
11

Churn

Bring the cream to about 15 °C: in warm weather set a tray of ice in the chamber under the box, in cold weather a tray of warm water, and shut the door. Pour in about 12 litres of heavy cream, keeping it 20 mm below the shaft, and check it with the thermometer. Turn the crank steadily and time it. When the butter comes, lift the container out, pour off the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.

Матеріали для цього кроку:

Жирні вершкиЖирні вершки12 l
Колотий лідКолотий лід2 кг
Крупна морська сільКрупна морська сіль1 штука
ВодаВода1 штука

Необхідні інструменти ({count})

Термометр зі щупом, що лишається в стравіТермометр зі щупом, що лишається в страві
СекундомірСекундомір
Цифрові кухонні вагиЦифрові кухонні ваги
Велика миска з нержавкої сталіВелика миска з нержавкої сталі
12

Troubleshooting

Spiral-beater churn troubleshooting.

Flow

Loading...
13

History and honest limits

**Harry Robie** and **Royal V. Robie** of Eaton, Madison County, New York, US 22,090, 16 November 1858, "Churn". They knew beaters set spirally round a level shaft were old, and claimed only the diamond-holed beater B with the hollow-ended beater C and the passage under their narrow bases. They gave no sizes or materials and no number of beaters: ours are seven at 50 mm and a quarter turn apart, blades turned 30 degrees. Their box (Fig. 1) has a rounded floor; our container is flat.

Матеріали

15

Необхідні інструменти

16

Файли дизайну

5

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...