Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Expanding Book Support: Lazy-Tongs Between Two End Pieces, Locked by a Thumb-Nut (Roseboom, 1901)
Forge

Створено

Forge

13. листопад 2026NO
6
0
0
0
0

Expanding Book Support: Lazy-Tongs Between Two End Pieces, Locked by a Thumb-Nut (Roseboom, 1901)

Jesse Roseboom of Cincinnati received US 668,961, dated 26 February 1901, for a book support that fills any gap on a shelf. Two end pieces are joined by a lazy-tongs; set it between the books and the shelf's side, open it until the books stand up firmly, and tighten a thumb-nut on the centre bolt, where two roughened disks lock the levers. We make it from hardwood and flat bar. All sizes are ours.
Початківець
About 3 hours

Інструкції

1

How far it opens

Завантаження блокнота Jupyter…
2

Read US 668,961

"It is placed between two sets of books on a shelf or the like or between a row of books and an upright of the shelf, and the connection B is then expanded, so as to press the end pieces against the upright and the adjacent book, after which the connection is adjustably fixed."
3

Make the end pieces

Cut two hardwood end pieces about as tall as your books' lower half (ours), his end pieces A, and sand them. Screw a small butt hinge to the middle of each inner face, his hinge-plates E, with the knuckle upright.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини1 штука
Карткова завісаКарткова завіса2 штук
Шурупи по деревуШурупи по дереву1 штука

Необхідні інструменти ({count})

Ручна пилкаРучна пилка
Наждачний папірНаждачний папір
Набір викрутокНабір викруток
4

Make the levers

Cut two long levers C and four short levers D of flat bar, round the ends and drill them at the notebook's centres. Drill the long levers at their middles for the bolt. File two washers rough on one face and fix one to each long lever round its centre hole, his corrugated disks H.

Матеріали для цього кроку:

Смуга з маловуглецевої сталіСмуга з маловуглецевої сталі1 штука
Плоска шайбаПлоска шайба1 штука

Необхідні інструменти ({count})

Ножівка по металуНожівка по металу
Набір напилківНабір напилків
Свердлильний верстатСвердлильний верстат
Набір сверделНабір свердел
Слюсарні лещатаСлюсарні лещата
5

Assemble the lazy-tongs

Bolt the long levers together at their centres with the rough faces meeting and a wing nut on the bolt, his bolt F and thumb-nut G. Rivet a short lever to each arm end of the long levers, loosely so they turn, and rivet the other ends of each pair to the free leaf of an end piece's hinge. The long levers' ends should bear on the end pieces and keep them upright.

Матеріали для цього кроку:

Гвинт із циліндричною головкою та внутрішнім шестигранникомГвинт із циліндричною головкою та внутрішнім шестигранником1 штука
Гайка-баранецьГайка-баранець1 штука
Сталеві заклепкиСталеві заклепки1 штука

Необхідні інструменти ({count})

Слюсарний молоток із кульковим бойкомСлюсарний молоток із кульковим бойком
КернерКернер
Розвідний ключРозвідний ключ
6

Use it

Set it in the gap on the shelf, open it until both end pieces press the books and the shelf's side, and tighten the wing nut. Loosen the nut to close it up and move it.
7

Troubleshooting

Book support troubleshooting.

Flow

Loading...
8

History and honest limits

**Jesse Roseboom** of Cincinnati, US 668,961, dated 26 February 1901, filed 7 August 1900. He claimed "a book-support for use on shelves and the like, comprising end pieces, and the long and short levers interposed between the end pieces; the long levers being pivotally connected together, and the short levers being pivotally connected to the arms of the long levers, and to the end pieces", and the roughened meeting faces with bolt and nut. He gives no sizes; the hardwood, flat bar, hinges as his hinge-plates, rivets and all sizes are ours.

Матеріали

8

Необхідні інструменти

11

За цим кресленням виготовляють

Пов'язані креслення

Ці креслення діляться знаннями — техніки, матеріали або принципи

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...