Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
False-Bottom Jet Churn: Paddles Under a Pierced Partition Draw Cream Down at the Centre and Jet It Up at the Rim
Buttercup

Створено

Buttercup

11. листопад 2026IE
11
0
0
0
0

False-Bottom Jet Churn: Paddles Under a Pierced Partition Draw Cream Down at the Centre and Jet It Up at the Rim

James Sangster of Buffalo, New York, received US 27,570, dated 20 March 1860, for a churn. A false bottom divides the churn; paddles spinning beneath it draw the cream and air down through holes near its centre and throw it up through holes near its rim, under caps that aim the streams against each other. Another paddle turns above. The cream goes round and round, from rim to centre and back. The patent gives no sizes; every size here is ours.
Середній
About 2 days, plus printing

Інструкції

1

Down at the centre, up at the rim

Завантаження блокнота Jupyter…
2

An upright churn with a pierced cover, one week before

Wiswell's cover is above the scoops. Sangster's pierced partition is below the cream, with paddles under it.
3

Read US 27,570

"U and V represent caps which partially cover the apertures L and N. They are placed in such a position as to cause the fluid to flow in streams against each other, by boring the holes L and N at the same angles at which the caps U and V are set. The caps may be dispensed with and the same result obtained."
4

Print the caps Q, U, W, V

Hood cap 50 mm across, open on one side. Print four. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Файл дизайнуSTLCC0 - Free
5

Print the crown wheel

Crown wheel, 36 teeth on its face, module 2, with a hub; bored 12.4 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Файл дизайнуSTLCC0 - Free
6

Print the pinion

Spur pinion, 12 teeth, module 2, with a hub; bored 12.4 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Файл дизайнуSTLCC0 - Free
7

Rim Y and partition E

Screw a ring of HDPE strip 10 mm thick and 12 high inside the bucket with its top 60 mm above the floor, as the rim Y, sealing the screw holes outside with silicone. Cut a disc of 10 mm HDPE sheet to rest on it, bored 17 mm in the centre. Bore four 30 mm holes, H, I, J, K, 45 mm from the centre, a quarter turn apart, and four 25 mm holes, L, M, N, O, 112 mm from the centre between them, each bored at 45 degrees slanting toward the centre as it rises. Screw a printed cap over each rim hole, its open side toward the centre.

Матеріали для цього кроку:

Відро на 20 літрівВідро на 20 літрів1 штука
Лист ПЕВГЛист ПЕВГ1 штука
Машинні гвинтиМашинні гвинти16 штук
Силіконовий герметикСиліконовий герметик1 штука

Необхідні інструменти ({count})

ЕлектролобзикЕлектролобзик
Набір кільцевих пилокНабір кільцевих пилок
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
ТранспортирТранспортир
Напилки (ручний напилок)Напилки (ручний напилок)
Набір викрутокНабір викруток
8

Spindle D, paddles C, G and Z, shoulder J'

Screw a hardwood block 50 x 50 x 6 mm to the floor's centre and bore it 17 mm, 5 deep, as the step. Cut a 16 mm stainless spindle 435 mm long and turn or file its top 75 mm down to 12 mm. Fix a hardwood paddle bar 250 x 45 x 20 mm across it, 8 mm above the floor when the spindle stands in its step (the paddles C and G), pass it up through the partition, and fit a printed or hardwood collar 32 mm across and 20 high on it just above the partition as the shoulder J'. Fix a second paddle Z, 200 x 30 x 20 mm, across it 185 mm above the floor.

Матеріали для цього кроку:

Пруток із нержавкої сталіПруток із нержавкої сталі1 штука
Дошка з твердої деревиниДошка з твердої деревини1 штука
Брусок твердої деревиниБрусок твердої деревини1 штука
Столярний клейСтолярний клей1 штука
Шурупи по деревуШурупи по дереву2 штук
Shaft CollarShaft Collar2 штук
ШплінтШплінт2 штук

Необхідні інструменти ({count})

Ножівка по металуНожівка по металу
Напилки (ручний напилок)Напилки (ручний напилок)
Слюсарні лещатаСлюсарні лещата
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Циркулярний верстатЦиркулярний верстат
Наждачний папірНаждачний папір
Набір викрутокНабір викруток
9

Top I' and crank X

Cut a hardwood top 350 x 205 x 25 mm to sit on the bucket's rim and bore it 13 mm over the centre for the spindle; fit the pinion on the spindle above it. Screw two hardwood chairs on the top carrying a 12 mm stainless crank shaft with the crown wheel meshing the pinion, and fit a hardwood crank X with a dowel handle on its end.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини2 штук
Пруток із нержавкої сталіПруток із нержавкої сталі1 штука
Шканти з твердої деревиниШканти з твердої деревини1 штука
Столярний клейСтолярний клей1 штука
Шурупи по деревуШурупи по дереву8 штук
Shaft CollarShaft Collar2 штук
Філамент PETGФіламент PETG1 штука

Необхідні інструменти ({count})

3D-принтер FDM3D-принтер FDM
Циркулярний верстатЦиркулярний верстат
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Набір перових сверделНабір перових свердел
Ножівка по металуНожівка по металу
Струбцина з напрямноюСтрубцина з напрямною
Набір викрутокНабір викруток
РулеткаРулетка
10

The build in 3D

FreeCAD model of this build, the bucket cut through the middle: the paddles C and G under the partition E on its rim Y, the centre and rim holes with their caps, the shoulder J', the paddle Z, and the top with the crank, crown wheel and pinion.
Файл дизайнуBLENDCC0 - Free
11

Churn

Pour about 8 litres of heavy cream at about 15 °C, checked with the thermometer, into the bucket over the partition, set the top and gearing on the rim, and turn the crank steadily, timing it. When the butter comes, lift off the top, lift out the spindle and partition, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

Матеріали для цього кроку:

Жирні вершкиЖирні вершки8 l
Крупна морська сільКрупна морська сіль1 штука
ВодаВода1 штука

Необхідні інструменти ({count})

Термометр зі щупом, що лишається в стравіТермометр зі щупом, що лишається в страві
СекундомірСекундомір
Цифрові кухонні вагиЦифрові кухонні ваги
Велика миска з нержавкої сталіВелика миска з нержавкої сталі
12

Troubleshooting

False-bottom churn troubleshooting.

Flow

Loading...
13

History and honest limits

**James Sangster** of Buffalo, New York, US 27,570, 20 March 1860, "Churn". He claimed the paddles Z, C and G with the partition E pierced near its centre and near its rim under caps, "for the purpose of passing the cream around and around through the openings from circumference to center and vice versa". He made it of "wood, tin or any other suitable material"; ours is a food-grade bucket with an HDPE partition and printed caps and gears. Every size here is ours.

Матеріали

16

Необхідні інструменти

19

Файли дизайну

4

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...