Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Screw Eye: Parmelee's One-Piece Wire Eye with a Stop-Ring
Forge

Створено

Forge

26. жовтень 2026NO
24
0
0
0
0

Screw Eye: Parmelee's One-Piece Wire Eye with a Stop-Ring

A screw eye bent from one piece of wire, by Arthur W. Parmelee of Worcester, Massachusetts (US 350,209, 1886). One end is threaded to turn into wood, the other bent into a closed eye. His addition is a ring closed into a groove around the shank: it stops the screw at the right depth, looks neat, and is left a little loose so the eye can turn without marking the wood under it. The patent gives no metal or sizes. Iron wire, the 3 mm size, the pliers and the die are ours. The picture: Figs. 1-3 and 10-11 of the patent.
Початківець
30 minutes

Інструкції

1

Cut a piece of wire

Cut a straight piece of iron wire about 3 mm thick (ours), long enough for the screw, the shank and the eye (Fig. 1).

Матеріали для цього кроку:

Залізний дрітЗалізний дріт1 штука

Необхідні інструменти ({count})

ЛінійкаЛінійка
БокорізиБокорізи
2

Cut the groove

File a narrow groove right round the wire, a screw length from one end (Fig. 2). Parmelee cuts it or presses it in.

Необхідні інструменти ({count})

Набір надфілівНабір надфілів
Слюсарні лещатаСлюсарні лещата
3

Point the screw end

File that end to a tapering point (Fig. 3).

Необхідні інструменти ({count})

Напилок по металуНапилок по металу
Слюсарні лещатаСлюсарні лещата
4

Thread the screw end

Cut a screw thread on the pointed end "in the usual way". Ours: a die in a die stock, run on as far as the point allows.

Необхідні інструменти ({count})

ПлашкотримачПлашкотримач
Слюсарні лещатаСлюсарні лещата
5

Bend the eye

Bend the other end into a closed round eye, the end turned in against the shank (Fig. 10).

Необхідні інструменти ({count})

КруглогубціКруглогубці
ПлоскогубціПлоскогубці
6

Make the split ring

Bend a short piece of the same wire round into an open ring that just slips over the shank (Figs. 9 and 11).

Матеріали для цього кроку:

Залізний дрітЗалізний дріт1 штука

Необхідні інструменти ({count})

БокорізиБокорізи
КруглогубціКруглогубці
7

Close the ring into the groove

Slide the ring onto the groove and squeeze it until its two ends meet in a continuous band. Leave it a little loose, so the eye turns while the ring stays still against the wood.

Необхідні інструменти ({count})

ПлоскогубціПлоскогубці
8

Turn it into the wood

Turn the screw into the wood by the eye until the ring meets the surface: the ring is the depth stop. Parmelee also allows washers under the ring; we leave them out.

Матеріали

1

Необхідні інструменти

8

За цим кресленням виготовляють

Пов'язані креслення

Ці креслення діляться знаннями — техніки, матеріали або принципи

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...