Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Renewable Rubber-Face Hammer: Rolled Faces Pressed Onto Pronged Discs, Driven Out Through a Notch When Worn (Sewell, 1928)
Forge

Створено

Forge

13. листопад 2026NO
8
0
0
0
0

Renewable Rubber-Face Hammer: Rolled Faces Pressed Onto Pronged Discs, Driven Out Through a Notch When Worn (Sewell, 1928)

Albert G. Sewell received US 1,674,999, dated 26 June 1928, for a soft-face hammer whose worn faces can be renewed instead of throwing the hammer away. Each end of the head is a cup. A face rolled from a strip is pressed into the cup onto a loose sheet-metal disc whose prongs bite into it and wedge it tight. When a face is battered, a rod pushed through a notch at the bottom of the cup drives the disc and the face out together, and a new face goes in. He preferred rawhide and named rubber among face materials; ours are rolled from rubber sheet. The patent gives no sizes; every size here is ours.
Середній
About 1 day

Інструкції

1

Rolling a face plug

Завантаження блокнота Jupyter…
2

Read US 1,674,999

"Thus, by hammering or otherwise thrusting a rod or suitable device against the wedging member, the latter, with the striking face member, can be forced or driven out of the socket or recess, after which a new striking face member may be forced into the socket, to be secured therein by the wedging member."
3

Turn the head

Grip 40 mm steel round bar in the chuck and turn a head 110 mm long: the two ends stay 40 mm across for 26 mm as the flanges D, and the middle is waisted to 30 mm. Bore each end 32 mm across and 22 mm deep for the sockets C, flat at the bottom. Drill a 20 mm eye B through the middle, square to the axis, in a V-block on the drill press.

Матеріали для цього кроку:

Круглий пруток з маловуглецевої сталіКруглий пруток з маловуглецевої сталі1 штука
Мастильно-охолоджувальна оливаМастильно-охолоджувальна олива1 штука

Необхідні інструменти ({count})

Токарний верстат по металуТокарний верстат по металу
Трикулачковий токарний патронТрикулачковий токарний патрон
Токарний різецьТокарний різець
Розточна оправкаРозточна оправка
Відрізний різецьВідрізний різець
Свердлильний верстатСвердлильний верстат
Розмічальна призмаРозмічальна призма
Набір сверделНабір свердел
Цифровий штангенциркуль 6 дюймівЦифровий штангенциркуль 6 дюймів
Захисні окуляриЗахисні окуляри
4

Cut the notches K

On the handle's side of each flange, saw and file a notch 8 mm wide through the flange's wall at the very bottom of the socket, so a rod can be pushed in at a slant against the edge of the disc at the bottom.

Необхідні інструменти ({count})

Слюсарні лещатаСлюсарні лещата
Ножівка по металуНожівка по металу
Набір напилківНабір напилків
КернерКернер
5

Pronged discs G

Cut two discs of 1.5 mm steel sheet 31.5 mm across. At four places round each rim, snip two cuts 6 mm deep 5 mm apart and bend the tab between them up at a right angle with the pliers: the prongs H. Drop one disc loosely into the bottom of each socket, prongs out.

Матеріали для цього кроку:

Лист маловуглецевої сталіЛист маловуглецевої сталі1 штука

Необхідні інструменти ({count})

Ножиці по металуНожиці по металу
ПлоскогубціПлоскогубці
Слюсарні лещатаСлюсарні лещата
Набір напилківНабір напилків
6

Roll and press in the faces E

Cut two strips of 3 mm natural rubber sheet 32 mm wide and about 270 mm long. Roll each tightly into a coil, trimming the strip until the coil just enters a socket, and tie it. Press the coil into its socket in the vice, between soft packing, until it bottoms on the disc and its prongs bite in, leaving the face standing about 10 mm out. Cut the tie and trim the face flat with the knife.

Матеріали для цього кроку:

Аркуш натурального каучукуАркуш натурального каучуку1 штука

Необхідні інструменти ({count})

Макетний ніжМакетний ніж
Слюсарні лещатаСлюсарні лещата
Цифровий штангенциркуль 6 дюймівЦифровий штангенциркуль 6 дюймів
7

Handle

Turn an ash handle 300 mm long, its end a tight fit in the eye. Saw a slot down its end, drive it into the eye, and glue and drive a hardwood wedge into the slot; saw it off flush.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини1 штука
Столярний клейСтолярний клей1 штука

Необхідні інструменти ({count})

Токарний верстат по деревуТокарний верстат по дереву
Набір токарних різців по дереву (HSS)Набір токарних різців по дереву (HSS)
Ножівка по металуНожівка по металу
Слюсарний молоток із кульковим бойкомСлюсарний молоток із кульковим бойком
8

Renew a face

When a face is worn, push a steel rod through the socket's notch against the disc's edge and tap it out with the hammer; the disc and the face come out together. Put the disc back, prongs out, and press in a new rolled face.

Необхідні інструменти ({count})

Слюсарний молоток із кульковим бойкомСлюсарний молоток із кульковим бойком
Слюсарні лещатаСлюсарні лещата
9

Troubleshooting

Soft-face hammer troubleshooting.

Flow

Loading...
10

History and honest limits

**Albert G. Sewell**, US 1,674,999, dated 26 June 1928, filed 25 July 1927. He describes a head with a socket at each end formed by annular flanges, a striking face member of relatively soft material rolled from a strip and pressed in as a plug, a loose sheet-metal wedging disc with prongs in the socket's bottom, and openings through which a rod drives the disc and face out. He preferred rawhide and his head was cast iron; ours is turned steel with faces rolled from rubber sheet, which he lists among the face materials in use. He gives no sizes; every size here is ours.

Матеріали

6

Необхідні інструменти

20

За цим кресленням виготовляють

Пов'язані креслення

Ці креслення діляться знаннями — техніки, матеріали або принципи

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...