Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Soldering Station: a Stand Whose Bimetal Switch Reads the Iron's Heat (Birk, Hart Mfg., US 2,248,486, 1941)
Ed

Створено

Ed

3. листопад 2026FI
4
0
0
0
0

Soldering Station: a Stand Whose Bimetal Switch Reads the Iron's Heat (Birk, Hart Mfg., US 2,248,486, 1941)

A soldering station: an ordinary electric iron plugs into its stand, and the stand controls it. When the iron is laid in the stand's trough, its heater housing sits over a flue with a U-shaped bimetal switch inside; the heat it gives off opens the switch at the temperature you set with a screw, and closes it again as it cools. A red lamp shows the iron heating, a green lamp shows it hot and idling. Result: a stand that keeps an electric iron at a set temperature between jobs and shows its state. Source: H. W. Birk (Hart Manufacturing), US 2,248,486 (1941). Unknown: sizes, the bimetal, the lamps. Picture: the patent drawing.
Середній
Unknown

Інструкції

1

Make the stand

Cast or form a box-shaped stand in one piece from a fire-resistant material such as porcelain: a high front wall, a low back wall, two side walls and a top sloping down about 10° toward the back, with feet at the corners so air can pass beneath. Close the bottom with a removable plate screwed to a flange and pierced with air holes. In the top, hollow a trough shaped to the iron's heater housing, ending at a shoulder, then a narrower groove for the tip. Cut a flue through the top along the trough, under a cover with holes. Ours: porcelain. Not given: sizes.

Матеріали для цього кроку:

Невідомий матеріалНевідомий матеріал1 porcelain stand
Невідомий металНевідомий метал1 bottom plate, screws

Необхідні інструменти ({count})

Невідомі розміриНевідомі розміри
2

Fit the bimetal switch

Bend a strip of bimetal into a U whose legs spread apart when cool and close together when hot. Rivet one leg to a metal strip fixed beside the flue (on an insulating bracket if the stand conducts); put a contact on the free leg's end. Face it with a fixed contact on a screw stud threaded through a metal plate and out through the side wall in an insulating sleeve, slotted for a screwdriver: turning it sets the temperature, low for wax melting or high for electric branding irons. Not given: the bimetal, the contact metal.

Матеріали для цього кроку:

Біметалева пластинаБіметалева пластина1 штука
Невідомий металНевідомий метал1 strips, plate, contacts, stud
Невідомий ізоляційний матеріалНевідомий ізоляційний матеріал1 bracket, sleeve, plate

Необхідні інструменти ({count})

Клепальний набірКлепальний набір
Набір мітчиків і плашокНабір мітчиків і плашок
3

Wire the outlet and lamps

Set an outlet in a side wall for the iron's plug, held by a flange and a split ring, and wire it in series with the switch to the supply cord. At the top of the front wall, set two lamp sockets at about 45°, one with a red lens and one with a green: wire the red in parallel with the iron's heater, the green in parallel with the switch. Not given: the lamp ratings, the outlet type.

Матеріали для цього кроку:

Невідомий роз’ємНевідомий роз’єм1 outlet
Ламповий патронЛамповий патрон2 штук
Лампа розжаренняЛампа розжарення2 штук
Невідомий матеріалНевідомий матеріал2 red and green lenses
Гнучкий шнур із вилкоюГнучкий шнур із вилкою1 штука

Необхідні інструменти ({count})

Набір викрутокНабір викруток
4

Use it

Set the temperature by turning the slotted stud with a screwdriver. Plug an electric soldering iron into the stand's outlet and lay it in the trough so its heater housing closes the flue. While the bimetal is cool the switch is closed and the red lamp lights: the iron heats. At the set temperature the switch opens; the green lamp glows, the red goes dark and the iron idles. Lift the iron off and air rushes up the flue, cooling the bimetal so the iron heats again. Because it senses the heater, not the tip, the heater cannot burn out even if the tip is loose.

Матеріали для цього кроку:

ПаяльникПаяльник1 electric soldering iron

Необхідні інструменти ({count})

Набір викрутокНабір викруток

Матеріали

9

Необхідні інструменти

4

За цим кресленням виготовляють

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...