Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Solenoid: Iron-Clad Valve Magnet with Two Coils, 1860 and 1765 Turns (Nachod 1905, in Underhill 1910)
Charlie

Створено

Charlie

31. жовтень 2026DE
12
0
0
0
0

Solenoid: Iron-Clad Valve Magnet with Two Coils, 1860 and 1765 Turns (Nachod 1905, in Underhill 1910)

A short-stroke solenoid that opens an air valve. One coil pulls the iron armature down; a second, weaker coil holds it there against the air pressure once the first is switched off. A cast-iron shell closes the magnetic circuit around both. Result: an iron-clad plunger solenoid driving a brass valve rod through its hollow core. Source: C. P. Nachod's test (Electrical World, 1905) in Underhill, Solenoids, Electromagnets and Electromagnetic Windings (1910), pp. 125-129. Unknown: the wire insulation; the test does not give it. Not given: shell and armature sizes, voltage. Picture drawn by Youblob.
Просунутий
2 days

Інструкції

1

Turn the core and armature

Turn the core from Norway iron to 3.17 cm outside diameter and bore a 0.95 cm hole through it for the valve rod. Turn the armature from the same iron. Ours: wrought iron bar; the armature size is not given.

Матеріали для цього кроку:

Пруток кованого залізаПруток кованого заліза1 as required

Необхідні інструменти ({count})

Набір токарних різців по дереву (HSS)Набір токарних різців по дереву (HSS)
2

Cast the shell and top

Cast the shell and top in cast iron so they close the magnetic circuit round the coils, leaving a round clearance gap for the armature in the top. Sizes: not given (Underhill's Fig. 92 shows the layout).

Матеріали для цього кроку:

Чушки чавунуЧушки чавуну1 as required

Необхідні інструменти ({count})

ВагранкаВагранка
ОпокаОпока
Формувальний пісокФормувальний пісок
3

Wind coil A: 1860 turns of No. 25

Wind the operating coil, 1860 turns of No. 25 wire, and place it where it encircles the working air gap between armature and core. Copper, as Underhill gives for magnet windings. Unknown: the insulation; the test does not give it.

Матеріали для цього кроку:

Мідний дрітМідний дріт1 as required
Невідомий ізоляційний матеріалНевідомий ізоляційний матеріал1 as required

Необхідні інструменти ({count})

Набір токарних різців по дереву (HSS)Набір токарних різців по дереву (HSS)
4

Wind coil B: 1765 turns of No. 26

Wind the retaining coil, 1765 turns of No. 26 wire, and place it below coil A on the core. Being away from the gap, it pulls only 0.4-0.8 as hard as A, enough to hold the armature down.

Матеріали для цього кроку:

Мідний дрітМідний дріт1 as required

Необхідні інструменти ({count})

Набір токарних різців по дереву (HSS)Набір токарних різців по дереву (HSS)
5

Assemble with the brass valve rod

Fit core, coils and armature in the shell and pass the brass rod through the core to the valve. Nachod set test gaps of 0.41 and 2.05 mm with brass washers.

Матеріали для цього кроку:

Латунний прутокЛатунний пруток1 as required

Необхідні інструменти ({count})

Набір токарних різців по дереву (HSS)Набір токарних різців по дереву (HSS)

Матеріали

5

Необхідні інструменти

4

За цим кресленням виготовляють

Пов'язані креслення

Ці креслення діляться знаннями — техніки, матеріали або принципи

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...