Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Spanner Set: Open-End Wrenches for 1/4 to 1 Inch Bolts (Machinery's Handbook, 1924)
Forge

Створено

Forge

3. листопад 2026NO
7
0
0
0
0

Spanner Set: Open-End Wrenches for 1/4 to 1 Inch Bolts (Machinery's Handbook, 1924)

A set of open-end spanners made to the standard dimensions in Machinery's Handbook. The jaw opening fits the nut of each bolt size, and head width, head thickness and length grow with it, so each spanner is strong enough for its own nut. Variable: the bolt size. The table gives each spanner's dimensions from 1/4 in up to 3 1/2 in bolts; this set covers 1/4 to 1 in. Source: Machinery's Handbook (1924), p. 848, Dimensions of Wrenches. Unknown: the steel and its hardening. Picture: the Handbook's page.
Середній
Unknown

Інструкції

1

Pick the sizes

For each bolt size, the Handbook gives jaw opening A, head width B, head thickness H and overall length L, in inches. 1/4 in bolt: 1/2, 1, 1/4, 5 1/2. 5/16: 19/32, 1 3/16, 5/16, 6. 3/8: 11/16, 1 3/8, 3/8, 7. 7/16: 25/32, 1 9/16, 7/16, 8. 1/2: 7/8, 1 3/4, 1/2, 9. 9/16: 31/32, 1 15/16, 9/16, 10. 5/8: 1 1/16, 2 1/8, 5/8, 11. 3/4: 1 1/4, 2 1/2, 11/16, 12 1/2. 7/8: 1 7/16, 2 15/16, 3/4, 14 1/2. 1 in: 1 5/8, 3 5/16, 7/8, 16 1/2. The neck and handle sizes are in the same table. Ours: a set of these ten.

Необхідні інструменти ({count})

МікрометрМікрометр
2

Forge the blanks

Forge each spanner from bar: a round head as wide as B and as thick as H, a neck, and a handle to make the overall length L. Ours: carbon steel bar forged under a power hammer. Not given: the steel, the forging method.

Матеріали для цього кроку:

Пруток вуглецевої сталі (0,6 % C)Пруток вуглецевої сталі (0,6 % C)10 ten spanners

Необхідні інструменти ({count})

ГорноГорно
Механічний молотМеханічний молот
КовадлоКовадло
3

Cut the jaws and harden

Cut the open jaw in each head to the opening A, so it fits across the flats of that bolt's nut, and finish the faces parallel. Check each opening. Harden and temper the spanners. Not given: the hardening.

Необхідні інструменти ({count})

Фрезерний верстатФрезерний верстат
Напилок по металуНапилок по металу
МікрометрМікрометр
Піч для термообробкиПіч для термообробки
Гартівна діжкаГартівна діжка

Матеріали

1

Необхідні інструменти

8

За цим кресленням виготовляють

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...