Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Alcohol Burner: the Glass Spirit Lamp with a Copper Wick Shield (Morfit, 1849)
Charlie

Створено

Charlie

7. листопад 2026DE
11
0
0
0
0

Alcohol Burner: the Glass Spirit Lamp with a Copper Wick Shield (Morfit, 1849)

A small glass lamp that burns alcohol for heating test tubes and small vessels on the bench. Campbell Morfit (1849): the glass body holds the alcohol; a round copper shield with a tube in its centre carries a cotton wick and rests on the neck; a minute hole in the shield lets vapour escape; a glass cap ground to fit the neck keeps the alcohol from evaporating. Alcohol gives no smoke and does not blacken the glass. Sizes, and how the wick tube is fixed, are not given. Source: C. Morfit, Chemical and Pharmaceutic Manipulations (1849), pp. 160-162. Picture: Fig. 115.
Початківець
Unknown

Інструкції

1

Read Morfit

"To the neck b is adjusted a copper circular shield c, with a tube in its centre for the passage of the wick, which should be of cotton, and similar to that used for tallow candles. The shield should rest upon, rather than within the neck, otherwise its expansion by the heat may cause the breakage of the glass. A minute opening drilled in the shield is also requisite for the escape of vapor in case the alcohol should become heated."
2

Make the copper shield

Cut a round copper shield a little wider than the neck of the glass body, so it rests on the neck and not inside it. Fix a short copper tube through its centre for the wick (ours: soldered; the joint is not given). Drill a minute hole in the shield for vapour to escape. Sizes are not given (unknown).

Матеріали для цього кроку:

Мідний листМідний лист1 shield
Мідна трубаМідна труба1 wick tube
Олов'яно-свинцевий припійОлов'яно-свинцевий припій1 joint
ФлюсФлюс1 joint

Необхідні інструменти ({count})

Ножиці по металуНожиці по металу
ПаяльникПаяльник
Ручний дрильРучний дриль
Невідомі розміриНевідомі розміри
3

Fit the wick and the body

Draw a cotton wick of the tallow-candle kind through the tube so it reaches down into the glass body, which is the alcohol reservoir. Set the shield on the neck. Ours: a clear glass bottle as the body.

Матеріали для цього кроку:

Скляна бутля (прозора)Скляна бутля (прозора)1 body
Бавовняний ґніт для свічкиБавовняний ґніт для свічки1 штука

Необхідні інструменти ({count})

Ножиці по металуНожиці по металу
4

Fit the glass cap

Cover the wick, when the lamp is not in use, with a glass cap ground inside to fit the neck closely. It stops the alcohol evaporating and the wick taking up water, which makes relighting difficult. Put it on only after the lamp is out. How the cap is made and ground is not given (unknown).

Матеріали для цього кроку:

Невідоме склоНевідоме скло1 cap

Необхідні інструменти ({count})

Невідомі розміриНевідомі розміри
5

Fill and use

Morfit burns alcohol of about specific gravity 0.85. Always put the lamp out before refilling, then pour the spirit in gently until the reservoir is nearly full. The flame is hottest just below its tip; bring the vessel to it gradually, and spread the heat with copper gauze between flame and vessel for larger surfaces.

Матеріали

7

Необхідні інструменти

4

За цим кресленням виготовляють

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...