Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Oblique Perforated-Dasher Churn: A Slanted Spindle Drives the Cream Down and Sideways, a Guard Turns It Back
Buttercup

Створено

Buttercup

11. листопад 2026IE
9
0
0
0
0

Oblique Perforated-Dasher Churn: A Slanted Spindle Drives the Cream Down and Sideways, a Guard Turns It Back

E. N. Sprinkle of Marion, Virginia, received US 25,985, dated 1 November 1859, for a churn. Three perforated dashers turn on a spindle set slantwise across the churn, from a standard low on one side to a slot in the rim on the other, and a crank on its end turns it fast. The cream is driven down and towards one side and cut by the holes' edges; a sloping guard under the dashers sends it back up to them, and the bottom stays clear for gathering the butter. The patent gives no sizes; every size here is ours.
Початківець
About a day, plus printing

Інструкції

1

The spindle's slope, and where the cream goes

Завантаження блокнота Jupyter…
2

A turning dasher with curved wings, seven weeks before

Hassler's dasher stands upright. Sprinkle tilts his spindle so the dashers drive the cream sideways too.
3

Read US 25,985

"By reason of the dashers being operated in an oblique position, it will be seen that the cream will not only be forced down but will also be forced toward the side of the churn which supports the upper end of the dasher shaft, and is thus not only effectually agitated by the motion of the dashers, but is also cut and stirred by the edges of the perforations c, c, c, in the dashers"
4

Print the dashers C

Three perforated half-ellipse blades, 210 x 80 mm and 4 mm thick, round a 24 mm tube bored 12.6 mm, with a cross hole for a pin. Print with supports. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Файл дизайнуSTLCC0 - Free
5

Print the standard f

A post 30 mm square and 178 mm tall on a 60 mm base with an M6 nut trap, its top bored 12.8 mm at 38 degrees for the spindle's lower end, e. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Файл дизайнуSTLCC0 - Free
6

Print the guard's leg

A leg 24 mm across and 92 mm tall on a 50 mm foot, to hold the guard's low end. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Файл дизайнуSTLCC0 - Free
7

Standard f, guard F and slot h

Drill a 6.5 mm hole in the bucket's floor 115 mm from its centre. Push an M6 nut into the standard's trap, lay an O-ring under its base and bolt it over the hole from underneath, its sloping bore facing across the bucket. Cut the guard F from 8 mm hardwood: a half-circle to fit the bucket 110 mm up, notched round the standard. Screw it to the standard's side 125 mm up and onto its leg, 95 mm up at the far end, on one side of the spindle's line. Cut a slot 13 mm wide and 12 mm deep in the rim opposite the standard, and screw an eye h' beside it.

Матеріали для цього кроку:

Відро на 20 літрівВідро на 20 літрів1 штука
Набір шестигранних болтівНабір шестигранних болтів1 штука
Шестигранна гайкаШестигранна гайка1 штука
Плоска шайбаПлоска шайба1 штука
Ущільнювальне кільце круглого перерізуУщільнювальне кільце круглого перерізу1 штука
Дошка з твердої деревиниДошка з твердої деревини1 штука
Шурупи по деревуШурупи по дереву4 штук
Гачок і петляГачок і петля1 штука
Філамент PETGФіламент PETG1 штука

Необхідні інструменти ({count})

3D-принтер FDM3D-принтер FDM
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
ЕлектролобзикЕлектролобзик
КомпасКомпас
Ножівка по металуНожівка по металу
Напилки (ручний напилок)Напилки (ручний напилок)
Розвідний ключРозвідний ключ
Набір викрутокНабір викруток
8

Spindle D and crank E

Cut 12 mm stainless rod 625 mm long. Heat 415 mm from one end with the torch and bend it at right angles, then 120 mm further on bend it back parallel to make the crank. Slide the dasher onto the straight part and pin it 70 mm from the end. Set the end into the standard's bore and lay the spindle in the slot, then hook the catch g over it into the eye.

Матеріали для цього кроку:

Пруток із нержавкої сталіПруток із нержавкої сталі1 штука

Необхідні інструменти ({count})

Пропановий пальникПропановий пальник
Слюсарні лещатаСлюсарні лещата
МолотокМолоток
Термостійкі рукавиціТермостійкі рукавиці
Ножівка по металуНожівка по металу
Напилки (ручний напилок)Напилки (ручний напилок)
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
9

Cover B

Cut a hardwood cover to sit on the rim, with a notch for the spindle at the slot, a 10 mm vent hole j, and a screw eye in the middle with a ring of stainless wire for lifting, i.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини1 штука
Шуруп-кільцеШуруп-кільце1 штука
Дріт із нержавкої сталіДріт із нержавкої сталі1 штука

Необхідні інструменти ({count})

ЕлектролобзикЕлектролобзик
КомпасКомпас
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Наждачний папірНаждачний папір
10

The build in 3D

FreeCAD model of this build, the bucket and cover cut through the middle: the standard, the slanting spindle with its crank, the three-bladed dasher, and the guard on its leg. The dasher was turned through 24 angles.
Файл дизайнуBLENDCC0 - Free
11

Churn

Pour about 6 litres of heavy cream at about 15 °C into the bucket, checked with the thermometer, and put the cover on. Turn the crank fast and steadily, timing it. When the butter comes, unhook the catch, lift the spindle and dasher out, gather the butter from the clear bottom, drain the buttermilk, wash the butter in cold water until it runs clear, salt and weigh it.

Матеріали для цього кроку:

Жирні вершкиЖирні вершки6 l
Крупна морська сільКрупна морська сіль1 штука
ВодаВода1 штука

Необхідні інструменти ({count})

Термометр зі щупом, що лишається в стравіТермометр зі щупом, що лишається в страві
СекундомірСекундомір
Цифрові кухонні вагиЦифрові кухонні ваги
Велика миска з нержавкої сталіВелика миска з нержавкої сталі
12

Troubleshooting

Oblique dasher churn troubleshooting.

Flow

Loading...
13

History and honest limits

**E. N. Sprinkle** of Marion, Smyth County, Virginia, US 25,985, 1 November 1859, "Churn". He claimed, as an improvement on the churn patented to Hatfield and Goldsmith on 13 July 1858, "the combination of the perforated obliquely arranged dashers C, C, C, with the single inclined stationary guard F". The patent gives no sizes; every size here is ours. His cover is conical; ours is flat.

Матеріали

15

Необхідні інструменти

18

Файли дизайну

4

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...