Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Steam Boiler: Small Brass Shell Boiler, Screwed and Soldered (Hopkins, Model Engines and Small Boats, 1898)
Volt

Створено

Volt

3. листопад 2026SE
12
0
0
2
0

Steam Boiler: Small Brass Shell Boiler, Screwed and Soldered (Hopkins, Model Engines and Small Boats, 1898)

A small steam boiler for model engines and boats: a brass cylinder 4 in across, closed by two brass heads tied together by a brass stay rod, its seam held by two rows of brass screws and sealed with solder. It sits in a russia-iron jacket over an alcohol lamp, with a weighted safety valve and fusible plugs that put the lamp out if the water runs low. Result: a strong little shell boiler, 6 to 12 in long to suit the engine. Source: N. M. Hopkins, Model Engines and Small Boats (1898), ch. III. Unknown: the working pressure and the valve's sizes. Picture: the book's Fig. 33.
Середній
Unknown

Інструкції

1

Make the heads and stay

Cut two brass disks 4 in across and about 1/8 in thick, each with a 1/4 in hole in the centre, and true them up in the lathe. Pass a 1/4 in brass rod through both and solder it, with plenty of solder inside the heads to make them steam-tight. Screw heavy brass disks (round nuts are better than square) onto the rod ends against the heads. Set the heads 10 in apart over their outsides; about 6 in will do for a small single-acting engine, 7 in for a double engine, up to 12 in for a larger one.

Матеріали для цього кроку:

Латунний круглий прутокЛатунний круглий пруток1 two heads, two nuts
Латунний прутокЛатунний пруток1 1/4 in stay
Олов'яно-свинцевий припійОлов'яно-свинцевий припій1 as needed
ФлюсФлюс1 as needed

Необхідні інструменти ({count})

Токарний верстат по металуТокарний верстат по металу
Пальник БунзенаПальник Бунзена
2

Roll and screw the shell

Cut soft sheet brass at least 1/32 in thick (1/16 in for boilers over 8 in long), about 14 in long and 1/2 in longer than the heads so it overhangs 1/4 in each end. Roll it round the heads on tinner's rollers, never by hand, so it laps about 1 in. Slip it over the heads and rod and bind it tight with heavy twine. Drill two rows of holes along the lap, tap them and turn in little brass screws that go just through the under plate without projecting. Do not use iron screws: their rust pits the seams.

Матеріали для цього кроку:

Латунний листЛатунний лист1 shell
Машинні гвинтиМашинні гвинти1 small brass screws
Обв'язувальний шпагатОбв'язувальний шпагат1 binding

Необхідні інструменти ({count})

Тривалкові листозгинальні вальціТривалкові листозгинальні вальці
Ручний дрильРучний дриль
Набір мітчиків і плашокНабір мітчиків і плашок
3

Solder it up

Push the heads and rod out, hold the shell in a Bunsen flame and run solder well along the seam. Push the heads back and solder them all round the edge, and screw the nuts tight: the screws and stay take the strain, the solder keeps in the steam. Drill two or three 1/4 in holes in the top and bush them with heavy brass disks soldered on. For fusible plugs, drill two 1/4 in holes near the bottom and solder them shut with little brass caps.

Матеріали для цього кроку:

Олов'яно-свинцевий припійОлов'яно-свинцевий припій1 as needed
ФлюсФлюс1 as needed
Латунний круглий прутокЛатунний круглий пруток1 bushes and plug caps

Необхідні інструменти ({count})

Пальник БунзенаПальник Бунзена
Ручний дрильРучний дриль
4

Fit the jacket and safety valve

Cut end supports from russia sheet iron to hold the boiler by its ends, with an opening for the alcohol lamp, and bend a russia-iron cover over it, riveted to the ends by little ears. Punch a row of small holes along the cover's lower edge to let air in for the lamp; the cover keeps in the heat and keeps draughts off the flame. Turn a small safety valve true in the lathe, grind it to its seat with emery and oil, and fit a lead weight on its bar. Not given: the valve's sizes.

Матеріали для цього кроку:

Російське листове залізоРосійське листове залізо1 ends and cover
Залізні заклепкиЗалізні заклепки1 small
Латунний круглий прутокЛатунний круглий пруток1 valve
СвинецьСвинець1 weight

Необхідні інструменти ({count})

Ножиці по металуНожиці по металу
Клепальний набірКлепальний набір
Токарний верстат по металуТокарний верстат по металу
Шкурка на тканинній основі (шмергельне полотно)Шкурка на тканинній основі (шмергельне полотно)
5

Fire and set it

Fill the boiler two-thirds full, connect the engine and light the alcohol lamp under it. If the valve blows off before the engine turns over, move the weight a little farther out until the engine runs without steam escaping; well made, the valve will then blow off soon after the engine stops if the fire is left. If the water ever runs very low, the fusible plugs melt and the steam puts out the lamp. Do not try to burst a boiler to test it.

Необхідні інструменти ({count})

СпиртівкаСпиртівка

Матеріали

10

Необхідні інструменти

9

За цим кресленням виготовляють

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...