Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Steel Dowel Pins: Two from One Piece, Necked, Hardened and Ground (Stanley 1919)
Frank A. Stanley · Public domain (1919)
Forge

Створено

Forge

27. жовтень 2026NO
16
0
0
0
0

Steel Dowel Pins: Two from One Piece, Necked, Hardened and Ground (Stanley 1919)

Die makers made their own dowel pins two at a time: one piece of steel is turned, necked in the middle, hardened, ground dead straight to size from each end, then snapped in two at the neck. Frank Stanley described the practice of one die shop. Source: F. A. Stanley, Punches and Dies (1919), pp. 417–419. The choice of tool steel and the forge for hardening are ours; the passage gives no hardening heat. Picture: Stanley's Fig. 610, grinding dowel pins.
Середній
1 day

Інструкції

1

Cut stock for two pins

Take a length of steel a little larger than the dowel size and long enough for two pins. It must harden, so use tool steel (our choice).

Матеріали для цього кроку:

Восьмигранник з інструментальної сталіВосьмигранник з інструментальної сталі1 length for two pins

Необхідні інструменти ({count})

Слюсарні лещатаСлюсарні лещата
2

Turn 0.008 in over size

Turn it on centres to about 0.008 in above the finished size.

Необхідні інструменти ({count})

Токарний верстат по металуТокарний верстат по металу
Токарний хомутикТокарний хомутик
МікрометрМікрометр
3

Neck it in the middle

Cut a neck 1/16 in deep in the middle, the dividing line between the two pins.

Необхідні інструменти ({count})

Токарний верстат по металуТокарний верстат по металу
4

Harden

Harden the piece. This passage gives no heat; heat to hardening heat and quench in the usual way for your steel (ours).

Необхідні інструменти ({count})

Кувальне горноКувальне горно
ЩипціЩипці
Гартівна діжкаГартівна діжка
5

Grind each half to size

Put it on dead centres in the grinding machine and grind the diameter to size from one end to the neck. Reverse it on the centres and grind from the other end. The pins come out perfectly straight from end to end.

Необхідні інструменти ({count})

Круглошліфувальний верстатКруглошліфувальний верстат
Токарний хомутикТокарний хомутик
МікрометрМікрометр
6

Break the pins apart

Break the piece apart at the neck. You have two dowel pins ground closely to standard size; ream their holes true and straight to fit.

Необхідні інструменти ({count})

Слюсарні лещатаСлюсарні лещата

Матеріали

1

Необхідні інструменти

8

За цим кресленням виготовляють

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...