Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО

Youblob · CC0
55-Gallon Open-Head Steel Drum to ICC Specification 17H (1964)
The open-top 55-gallon (208-litre) steel drum, built to the rule US railways and shippers used for single-trip removable-head drums: welded low-carbon steel body, three rolled hoops, a crowned bottom, and a lid clamped by a bolted ring over a gasket.
Source: ICC Specification 17H, 49 CFR 78.118, Federal Register, 29 December 1964. The spec does not say how the bottom is joined. The litre figure, the gasket rubber and the machines are ours. Picture drawn by Youblob.
Просунутий
Production line
Інструкції
1
1
Cut low-carbon steel sheets
Cut low-carbon steel sheets
Use low-carbon steel for body and heads. For a 55-gallon drum: body 18 gauge, bottom head 18 gauge, removable head 14 gauge (16 gauge if the cover has one or more corrugations near its edge). 18 gauge is 0.0478 in nominal and at least 0.0428 in; 14 gauge 0.0747 in and at least 0.0677 in, measured at least 3/8 in from an edge.
Матеріали для цього кроку:
Лист маловуглецевої сталі1 body, bottom and lid sheetsНеобхідні інструменти ({count})
Ножиці по металу посилені
Мікрометр2
2
Roll and weld the body
Roll and weld the body
Roll the body sheet into a cylinder and weld the seam. The body seam must be welded.
Необхідні інструменти ({count})
Тривалкові листозгинальні вальці
Установка для зварювання шва труби3
3
Roll in three hoops
Roll in three hoops
Roll or swage three hoops into the body, one of them near the top curl.
Необхідні інструменти ({count})
Зигувальні ролики4
4
Press crowned heads
Press crowned heads
Press the bottom head crowned (convex) by at least 3/8 in, not standing out beyond the level of the chime, and fit it to the body. The spec does not say how the bottom is joined.
Необхідні інструменти ({count})
Штампувальний прес5
5
Make the bolted ring and gasket
Make the bolted ring and gasket
Make the closing ring from 12-gauge steel with drop-forged lugs, one of them threaded, and a 5/8 in bolt and nut (for drums over 30 gallons). Fit a gasket under the lid: gaskets are required.
Матеріали для цього кроку:
Лист маловуглецевої сталі1 12-gauge strip for the ring
Круглий пруток з маловуглецевої сталі1 for the lugs
Набір шестигранних болтів1 5/8 in bolt
Шестигранна гайка1 5/8 in
Гумовий лист1 gasketНеобхідні інструменти ({count})
Тривалкові листозгинальні вальці
Штампувальний молот зі штампами
Макетний ніж6
6
Check capacity and mark
Check capacity and mark
The drum must hold at least 4 % more than its marked 55 gallons, and no more than 5 % more (or 4 % plus 1 quart, whichever is greater). Emboss the marks: ICC-17H, STC (single-trip container), the maker, and the gauges, capacity and year.
Необхідні інструменти ({count})
Штампувальний прес7
7
Leak-test every drum
Leak-test every drum
Test each drum by air pressure inside of at least 7 psi with its seams under water or covered with soapsuds or heavy oil. Reject leakers, or repair them the way they were made and test again.
Матеріали для цього кроку:
Вода1 as requiredНеобхідні інструменти ({count})
Повітряний компресор
Манометр8
8
Type tests every four months
Type tests every four months
On drums taken at random and closed as for use: drop one filled with water to 98 % from 4 ft onto concrete so it lands diagonally on the chime, and hold another at 15 psi water pressure for 5 minutes. None may leak.
Матеріали для цього кроку:
Вода1 as requiredНеобхідні інструменти ({count})
МанометрМатеріали
6- 1 12-gauge strip for the ringЗаповнювач
- 1 for the lugsЗаповнювач
- 1 5/8 in boltЗаповнювач
- 1 5/8 inЗаповнювач
- 1 gasketЗаповнювач
- 2 as requiredЗаповнювач
Необхідні інструменти
10- Заповнювач
- Заповнювач
- Заповнювач
- Заповнювач
- Заповнювач
- Заповнювач
- Заповнювач
- Заповнювач
- 1 vendor sell this, none ship to you yetЗаповнювач
- Заповнювач
За цим кресленням виготовляють
CC0 Суспільне надбання
Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.
Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.
