Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
16 ft Canvas-Covered Cedar Canoe: Backbone, Seven Molds, Cedar Ribs and Planking, Glued Canvas (Boy Mechanic, 1919)
Woody

Створено

Woody

13. листопад 2026NO
6
0
0
0
0

16 ft Canvas-Covered Cedar Canoe: Backbone, Seven Molds, Cedar Ribs and Planking, Glued Canvas (Boy Mechanic, 1919)

Stillman Taylor's open Canadian canoe from The Boy Mechanic, Book 3 (1919): about 16 ft long, 31 in beam, 60 to 70 lb. Built upside down over a backbone and seven paper-pattern molds, with oak or ash stems, keelson and gunwales, 1/8 in cedar ribs and planking fastened with copper clout nails, then covered with No. 6 canvas laid in melted marine glue, painted, and varnished. Every layout dot and width is his, as printed.
Просунутий
Several weeks

Інструкції

1

His layout data

Завантаження блокнота Jupyter…
2

Read The Boy Mechanic, Book 3

"Working with light materials, the canoe builder must pay particular attention to the workmanship ... the work must not be hurried, but plenty of time taken to do each and every part well."
3

Get the materials

Stem: oak or ash 6 ft x 3/4 in square. Keelson: oak or ash 14 ft x 3-1/2 x 3/8 in. Gunwales: 2 of oak or ash 16 ft x 7/8 x 1/2 in. Seat risings: 2 of oak or ash 1/2 in square. Fenderwales: 34 ft of 1/2 in half-round molding. Outside keel (optional): oak 14 ft x 1 x 1/2 in. Deck beams: 2 of oak or ash 8 x 1-1/8 x 3/8 in. Seat frames: 2 at 30 x 3 x 3/4 and 2 at 12 x 2-1/4 x 3/4 in. Planking: cedar or pine, 100 sq ft, 1/8 in (25 ft of 1 in lumber dressed to 1/8 in, in 12, 14 and 16 ft lengths). Ribs: 360 running ft of cedar 1-3/4 x 1/8 in. Breast hooks: cedar or oak 32 x 9 x 3/4 in. Backbone, molds and ribbands from any cheap stuff. Fastenings: 1 lb 2 in wire nails; 1 lb 5/8 in and 1/2 lb 3/4 in copper clout nails; 18 brass screws 1-1/4 in No. 8 and 24 brass screws 1 in No. 6; 4 lb marine glue; 3 oz No. 2 copper tacks; 11-3/4 yd No. 6 canvas; 1 lb 3/8 in copper tacks. Rock elm or fir may replace oak or ash; spruce, pine, cypress or fir may replace cedar.

Матеріали для цього кроку:

Дошка з білого дубаДошка з білого дуба4 штук
Кедрова дошкаКедрова дошка6 штук
Соснова дошкаСоснова дошка3 штук

Необхідні інструменти ({count})

Ножівка для поздовжнього пилянняНожівка для поздовжнього пиляння
Ручна пилкаРучна пилка
Ручний рубанокРучний рубанок
РулеткаРулетка
4

Lay out the backbone and molds

Cut the backbone from a 16 ft x 4 x 7/8 in board, top edge 15 ft 8-3/4 in, and mark the mold stations from each end: 22-1/4 in to mold 1, then 23-1/4 in to mold 2 and 23-1/4 in to mold 3, each mold space 3/4 in thick; mold 4 sits at the centre; cut the ends off on the bevel (Fig. 1). Draw each mold on stiff paper from his rectangles, mortises and dots (notebook), trace the curve through the dots, cut out the half, fold and draw the other side, and cut the molds from 7/8 in stock: seven in all, numbered alike from each end: two No. 1, two No. 2 (each in halves), two No. 3 and one No. 4; nail battens across the halves.

Матеріали для цього кроку:

Соснова дошкаСоснова дошка2 штук
Аркуші щільного паперуАркуші щільного паперу1 штука
ЦвяхиЦвяхи1 штука

Необхідні інструменти ({count})

Ручна пилкаРучна пилка
Лобзикова пилкаЛобзикова пилка
ЛінійкаЛінійка
ОлівецьОлівець
НожиціНожиці
МолотокМолоток
5

Bend the stems and shape the keelson

Make the stem mold from his Fig. 6 pattern (24-1/2 x 12 in rectangle, dots in the notebook) and bend the straight-grained 3/4 in square oak or ash stems on it. Cut the keelson 13 ft 11 in long, tapering from 3-1/2 in at the centre: 3-1/2 in at 1 and 2 ft, 3-1/4, 2-5/8, 2 and 1-1/4 in at 3 to 6 ft, and 15/16 in at the ends (Fig. 7). Fasten each stem to the keelson with a couple of 3/4 in No. 10 screws.

Матеріали для цього кроку:

Дошка з білого дубаДошка з білого дуба2 штук
Латунні шурупи по деревуЛатунні шурупи по дереву4 штук

Необхідні інструменти ({count})

СкобельСкобель
Ручний рубанокРучний рубанок
Ручна пилкаРучна пилка
Коловорот із перкоюКоловорот із перкою
Викрутка пласкаВикрутка пласка
Струбцина типу CСтрубцина типу C
6

Set up the frame

Build it upside down: set the backbone on boxes about 1 ft or more off the floor and the molds in their numbered places, the backbone resting in their top mortises. True the molds with a square and toenail them. Lay the keelson in its mortises, fit the stems to the backbone angle and nail through the mold tops into them. Bevel the stem splice from the inside, leaving the outer edge about 1/8 in wide. Put on the gunwales at the sheer line with nails left proud, then four ribbands a side at 5 in centres from the keel, fastened with 1-1/4 in brads.

Матеріали для цього кроку:

Дошка з білого дубаДошка з білого дуба2 штук
Соснова дошкаСоснова дошка1 штука
ЦвяхиЦвяхи1 штука

Необхідні інструменти ({count})

Столярний косинецьСтолярний косинець
МолотокМолоток
СтамескиСтамески
Ручний рубанокРучний рубанок
7

Rib the hull

Saw cedar ribs 1-3/4 in wide and 1/8 in thick, cut to length gunwale to gunwale over the ribbands. Space them 3 in apart on centres along the keelson, one over each mold. Fasten each rib to the outside of the keelson with two 5/8 in copper clout nails, spring it in under the ribbands and fasten it to the gunwales. Then remove the ribbands.

Матеріали для цього кроку:

Кедрова дошкаКедрова дошка2 штук
Мідні цвяхи з широким капелюшкомМідні цвяхи з широким капелюшком1 штука

Необхідні інструменти ({count})

Ручна пилкаРучна пилка
МолотокМолоток
РулеткаРулетка
8

Plank the hull

Plank with 1/8 in cedar, bent cold, full length stem to stem, butted edge to edge without bevel, about 3 in wide; begin with the garboard strake at the keel and end with the sheer strake level with the gunwale. Punch nail holes with an awl, staggered along the ribs; clamp the plank, drive copper clout nails and clinch them inside on a clinch iron. Trim the plank ends to the stems and gunwales, saw the backbone in two to take out the frame, tack strips across the gunwales against sagging, and nail where the molds were.

Матеріали для цього кроку:

Кедрова дошкаКедрова дошка4 штук
Мідні цвяхи з широким капелюшкомМідні цвяхи з широким капелюшком1 штука
Мідні оббивні цвяшкиМідні оббивні цвяшки1 штука

Необхідні інструменти ({count})

ШилоШило
Струбцина типу CСтрубцина типу C
Підтримка для загинання цвяхівПідтримка для загинання цвяхів
МолотокМолоток
Ручна пилкаРучна пилка
9

Fit risings, seats, decks and thwarts

Nail 1/2 in square oak or ash seat risings, 14 ft long, about 4 in below the gunwale, boring first and clinching inside. Make the seat frames as Fig. 10 and cane them or tack on canvas (a kneeling paddler may use a 4 or 5 in seat bar instead). Notch the 8 x 1-1/8 x 3/8 in deck beams to wedge about 1/2 in against the gunwales (Fig. 11) and fix each with a 1-1/4 in No. 10 screw through the gunwale. Shape the decks 16 x 8 in (Fig. 12) and fix them with three 1-1/4 in No. 10 screws into the beam and three along each gunwale. Screw a centre thwart of oak or ash, 3/8 in thick, 2 in tapering to 1 in, under the gunwales amidships; extra thwarts behind the forward seat and about 3 ft forward of the rear seat stiffen it.

Матеріали для цього кроку:

Дошка з білого дубаДошка з білого дуба2 штук
Кедрова дошкаКедрова дошка1 штука
Мідні цвяхи з широким капелюшкомМідні цвяхи з широким капелюшком1 штука
Латунні шурупи по деревуЛатунні шурупи по дереву30 штук
ПарусинаПарусина1 штука

Необхідні інструменти ({count})

Коловорот із перкоюКоловорот із перкою
Викрутка пласкаВикрутка пласка
Ручна пилкаРучна пилка
СтамескиСтамески
МолотокМолоток
10

Lay the canvas

Lay the No. 6 canvas smoothly on the hull and trim it to fold at the stems (Fig. 13). Melt the black marine glue in a can over a moderately hot fire and spread a fairly heavy coat over one side of the canvas with a stiff brush. Lay it on and iron it with a moderately hot flatiron so the glue melts into the planking. Tack the edges along the gunwales and fold the canvas smoothly at the stems, tacking exactly down the stem centre line.

Матеріали для цього кроку:

ПарусинаПарусина1 штука
Морський клейМорський клей1 штука
Мідні оббивні цвяшкиМідні оббивні цвяшки1 штука

Необхідні інструменти ({count})

БляшанкаБляшанка
Широкий малярний пензельШирокий малярний пензель
Чавунна праскаЧавунна праска
НожиціНожиці
МолотокМолоток
11

Fenders, stem bands and keel

Tack 1/2 in round molding over the canvas edge (or a 1 in strip of planking with 1-1/4 in brads every 2 or 3 in). Put on stem bands of wood about 3/8 in square, rounded, with 1-1/4 in brads, or better, 3/8 in brass oval stem band with 3/4 in screws. An outside keel is optional: about 1 x 1/2 in of oak or ash tapered to the stem bands, or a flat keel about 2-1/2 in wide of 3/8 in oak or ash, which turns more easily and guards the bottom.

Матеріали для цього кроку:

Напівкругла дерев'яна розкладкаНапівкругла дерев'яна розкладка1 штука
Латунна накладка форштевняЛатунна накладка форштевня2 штук
Латунні шурупи по деревуЛатунні шурупи по дереву12 штук
Дошка з білого дубаДошка з білого дуба1 штука
ЦвяхиЦвяхи1 штука

Необхідні інструменти ({count})

МолотокМолоток
Викрутка пласкаВикрутка пласка
Ручний рубанокРучний рубанок
Ручний дрильРучний дриль
12

Paint and finish

Give the canvas a coat of shellac to waterproof it, then four coats of paint to fill the fibres, rubbing down the second and third with fine sandpaper. Finish all woodwork with three coats of good outside spar varnish. A removable slatted grating of soft-pine lattice, about 1-1/8 in wide and 1-1/4 in thick as printed, screwed to curved cross strips (not the ribs), protects the bottom.

Матеріали для цього кроку:

Шелаковий лакШелаковий лак1 штука
Олійна фарбаОлійна фарба1 штука
Наждачний папірНаждачний папір1 штука
Яхтовий лак (для рангоуту)Яхтовий лак (для рангоуту)1 штука
Соснова дошкаСоснова дошка1 штука

Необхідні інструменти ({count})

Широкий малярний пензельШирокий малярний пензель
Викрутка пласкаВикрутка пласка
13

Troubleshooting

Canoe troubleshooting.

Flow

Loading...
14

History and honest limits

From "How to Build a Canoe, Part I" by Stillman Taylor, in **The Boy Mechanic, Book 3**, Popular Mechanics, 1919 (Project Gutenberg 71856; checked on the archive.org scan boymechanic0003unse, pp. 77-84). As printed, his text differs in places: the backbone's lower edge is 1/2 in longer in one sentence and 1 in in the next; the list gives No. 8 deck screws, the text No. 10; the list's seat frames (30 x 3 and 12 x 2-1/4 in) differ from Fig. 10 (29 x 9 in); the fenders are half-round in the list and round in the text. The metric figures are ours.

Матеріали

16

Необхідні інструменти

21

За цим кресленням виготовляють

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...