МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
The Tank-Headed Self-Feeding Brush: Soap in the Tank, a Plate to Meter It
Martin

Створено

Martin

6. жовтень 2026NO
13
0
0
0
0

The Tank-Headed Self-Feeding Brush: Soap in the Tank, a Plate to Meter It

Scrubbing a floor means going back to the bucket every few strokes. Ernest N. Broderick of Indianapolis received US 639,348, dated 19 December 1899, for a cleaning brush with a small tank on its perforated top, fed through a hollow handle from a hose; a perforated plate slid by a screw sets how far the holes open, and soap in the tank turns the water to suds — "a self-feeding brush." This rung works out how the sliding plate opens the holes, then builds the tank on a scrub brush and measures the flow at each plate setting.
Середній
About 4 hours

Інструкції

1

Open area of the plate

Завантаження блокнота Jupyter…
2

A scrubbing brush before it

The embedded blueprint holds two brush heads on a sprung holder. Broderick puts a water tank on the head and feeds it through the handle.
3

Read US 639,348

"When used for scrubbing, the hose can be connected to a hydrant, and thus supply the desired amount of water to the brush, making it unnecessary to dip the brush into the bucket or tub of water. In other words, my device is a self-feeding brush. Should I desire to use soapy water, I can insert through the openings 10 particles of soap or soap powder. In this way I get soapsuds, which I use in scrubbing as it is needed, keeping the brush constantly supplied."
4

Perforate the brush back

Drill fourteen 4 mm holes through the scrub brush's back between the tufts, in two rows 30 mm apart.

Матеріали для цього кроку:

Жорстка щіткаЖорстка щітка1 штука

Необхідні інструменти ({count})

Слюсарні лещатаСлюсарні лещата
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Перманентний маркерПерманентний маркер
ЛінійкаЛінійка
Прозорі захисні окуляриПрозорі захисні окуляри
5

Make the sliding plate

Cut an aluminium plate 10 mm shorter than the back. Drill it through the back's holes, then file its end square. Rivet two guide strips to the back's top so it slides lengthwise.

Матеріали для цього кроку:

Алюмінієвий листАлюмінієвий лист1 штука
Витяжні заклепкиВитяжні заклепки1 штука

Необхідні інструменти ({count})

Ножиці по металуНожиці по металу
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Напилки (ручний напилок)Напилки (ручний напилок)
Набір заклепувальникаНабір заклепувальника
6

Build the tank

Fold an aluminium box 50 mm deep to the back's size with a lid. Drill the lid for a 25 mm filling hole and a handle socket. Seal it to the back with silicone and screws.

Матеріали для цього кроку:

Алюмінієвий листАлюмінієвий лист1 штука
Витяжні заклепкиВитяжні заклепки1 штука
Силіконовий герметикСиліконовий герметик1 штука
Шуруп по дереву #8 x 1"Шуруп по дереву #8 x 1"1 штука

Необхідні інструменти ({count})

Ножиці по металуНожиці по металу
Слюсарні лещатаСлюсарні лещата
Набір заклепувальникаНабір заклепувальника
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Шкіряні робочі рукавиціШкіряні робочі рукавиці
7

Fit the adjusting screw

Run an M4 screw through a nut epoxied on the tank's end wall so its tip pushes the plate. Turn it to close or open the holes.

Матеріали для цього кроку:

Машинні гвинтиМашинні гвинти1 штука
Шестигранна гайкаШестигранна гайка1 штука
Двокомпонентна епоксидкаДвокомпонентна епоксидка1 штука

Необхідні інструменти ({count})

Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Набір викрутокНабір викруток
8

Fit the handle

Fix 1.2 m of 15 mm copper tube in the socket with brass fittings. Fit a ball valve and hose connector at its top.

Матеріали для цього кроку:

Мідна трубаМідна труба1 штука
Латунні фітингиЛатунні фітинги1 штука
Кульовий кранКульовий кран1 штука
Ущільнювальна стрічка ПТФЕ для різьбиУщільнювальна стрічка ПТФЕ для різьби1 штука

Необхідні інструменти ({count})

ТруборізТруборіз
Розвідний ключРозвідний ключ
9

The patent drawing

US 639,348 drawing sheet, public domain (expired patent).
Крок 9 - Image 1
10

Measure the flow at each setting

Connect the garden hose. Set the plate fully open, half and nearly shut, and catch the water for 30 s each in the jug. Then add a squirt of soap through the filling hole and scrub.
Крок 10 - Image 1

Матеріали для цього кроку:

Садовий шлангСадовий шланг1 штука
ВодаВода1 штука
Кастильське мило (рідке)Кастильське мило (рідке)1 штука

Необхідні інструменти ({count})

Мірний глечикМірний глечик
СекундомірСекундомір
Цифровий штангенциркуль 6 дюймівЦифровий штангенциркуль 6 дюймів
11

A brush that floods, starves or leaks

Tank-headed self-feeding brush troubleshooting.

Flow

Loading...
12

History and honest limits

**Ernest N. Broderick** of Indianapolis filed US 639,348 on 6 February 1899; it is dated 19 December 1899. Rubber or leather strips seal the tank to the brush-top. Two hollow adjustable joints, ground to fit and clamped by a bolt, let the handle be set at any angle, for floors, walls, windows or dusting high furniture; with compressed air instead of water it blows dust away, and a mop or duster may replace the brush. **Honest limits.** Our handle is fixed; his joints are not built here. The notebook gives open area, not flow through a real hole. Your flows are the result.

Матеріали

15

Необхідні інструменти

16

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...