Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Hand Files Cut With a Double-Edged Hammer and Tempered in Burnt Ox Horn and Salt (Theophilus, 12th Century)
Forge

Створено

Forge

14. листопад 2026NO
8
0
0
0
0

Hand Files Cut With a Double-Edged Hammer and Tempered in Burnt Ox Horn and Salt (Theophilus, 12th Century)

How a medieval metalworker made his own files, from Theophilus's De Diversis Artibus (12th century): files of steel, or of soft iron faced with steel, forged to size, smoothed and cut with a double-edged hammer or cutting iron, then hardened by sprinkling them glowing with burnt ox horn and salt and quenching. Small soft-iron files are packed in lard, goatskin and clay instead.
Просунутий
About 1 day per few files

Інструкції

1

The hardening mix

Завантаження блокнота Jupyter…
2

Read De Diversis Artibus, Book III

"Files are made from pure steel, large and moderately sized, triangular and round. Others also are made which are stronger in the middle, from soft iron inside, but outwardly they are covered with steel."
3

Forge and smooth the blanks

Beat steel (or soft iron covered with steel) to the size and shape wanted: large or moderate, triangular or round; for small files, square, round, triangular or thin. Smooth them on a planing instrument (a filing or scraping bed).

Матеріали для цього кроку:

Пруток вуглецевої сталі (0,6 % C)Пруток вуглецевої сталі (0,6 % C)1 штука
Пруток кованого залізаПруток кованого заліза1 штука

Необхідні інструменти ({count})

ГорноГорно
Ковальський міхКовальський міх
КовадлоКовадло
МолотокМолоток
Ковальські кліщіКовальські кліщі
Напилки (ручний напилок)Напилки (ручний напилок)
4

Cut the teeth

Mark out the teeth with a hammer sharp on both sides, or with the cutting iron, until the file is cut all over.

Необхідні інструменти ({count})

МолотокМолоток
Зубило для насікання напилківЗубило для насікання напилків
КовадлоКовадло
Слюсарні лещатаСлюсарні лещата
5

Temper with horn and salt

Burn an ox horn in the fire, scrape it, mix it with a third part of salt and grind it hard. Heat the file until it glows, sprinkle the mixture over it everywhere, lay hot coals on and blow quickly over the whole without letting the coating fall off; then draw it out and quench it evenly in water, and dry it slightly over the fire. He tempers all steel things this way.

Матеріали для цього кроку:

Коров'ячий рігКоров'ячий ріг1 штука
СільСіль1 штука

Необхідні інструменти ({count})

ГорноГорно
Ковальський міхКовальський міх
ПіпеткаПіпетка
Ковальські кліщіКовальські кліщі
Гартівна діжкаГартівна діжка
6

Or pack small soft-iron files

For small soft-iron files, after cutting, anoint them with the grease of an old hog, bind them with small straps of buck-goat skin tied with flaxen thread, and cover each with beaten clay, leaving the handles (tangs) bare. Dry them, put them in the fire and blow strongly until the skin is burned, take them quickly out of the clay, quench evenly in water, and dry them at the fire.

Матеріали для цього кроку:

Свинячий жир (нутряне сало і хребтовий шпик)Свинячий жир (нутряне сало і хребтовий шпик)1 штука
Козяча шкіраКозяча шкіра1 штука
Лляна ниткаЛляна нитка1 штука
ГлинаГлина1 штука

Необхідні інструменти ({count})

ГорноГорно
Ковальський міхКовальський міх
Ковальські кліщіКовальські кліщі
Гартівна діжкаГартівна діжка
Ніж для шкіриНіж для шкіри
7

Troubleshooting

File troubleshooting.

Flow

Loading...
8

History and honest limits

From Theophilus Presbyter, **De Diversis Artibus** (12th century), Book III, chapters XVII-XIX, translated by Robert Hendrie (1847) (checked on the archive.org scan essayuponvarious00hend, pp. 223-225). He gives no sizes, temperatures or tooth spacing. The tools and the case-hardening explanation are ours.

Матеріали

8

Необхідні інструменти

11

За цим кресленням виготовляють

Пов'язані креслення

Ці креслення діляться знаннями — техніки, матеріали або принципи

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...