Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Silver Solder of Silver and Red Copper With a Burnt Wine-Stone Flux (Theophilus, 12th Century)
Forge

Створено

Forge

14. листопад 2026NO
5
0
0
0
0

Silver Solder of Silver and Red Copper With a Burnt Wine-Stone Flux (Theophilus, 12th Century)

How Theophilus soldered silver in the 12th century: an alloy of two parts pure silver and a third part red copper, rasped to filings, laid on a joint painted with a flux of burnt wine-stone (tartar) ground with water and salt, and flowed in the coals with a long gentle blast.
Середній
About half a day

Інструкції

1

The alloy

Завантаження блокнота Jupyter…
2

Read De Diversis Artibus, Book III

"Weigh two parts of pure silver, and a third (part) of red copper, and mix and finely rasp into a clean vessel."
3

Make the solder

Weigh two parts of pure silver and a third part of red copper, melt them together, and rasp the alloy finely into a clean vessel; keep the filings in a quill.

Матеріали для цього кроку:

Чисте сріблоЧисте срібло1 штука
МідьМідь1 штука

Необхідні інструменти ({count})

Важільні терезиВажільні терези
ТигельТигель
Кліщі для тиглівКліщі для тиглів
Кувальне горноКувальне горно
Ковальський міхКовальський міх
РашпільРашпіль
Перо для письмаПеро для письма
4

Make the flux

Take wine-stone from a vessel in which good wine has stood a long time, tie pieces in a cloth and put it in the fire until no more vapour comes from it. When cool, blow off the cloth ash and grind the burnt stone in a copper vessel with a round mallet, mixing in water and salt until it is as thick as lees.

Матеріали для цього кроку:

Винний камінь сирийВинний камінь сирий1 штука
Бавовняна тканинаБавовняна тканина1 штука
СільСіль1 штука

Необхідні інструменти ({count})

Кувальне горноКувальне горно
Відро на 20 літрівВідро на 20 літрів
Дерев'яний молоток (киянка)Дерев'яний молоток (киянка)
5

Solder

With a thin piece of wood paint the flux round the joint inside and out, shake the filed solder over it with a small iron, and dry it. Paint more flux on, more thickly than before, put the work in the fire, cover it with coals and blow gently with a long breath until the solder has melted. Take it out, let it cool slightly and wash it. If the joint is not firm, do it again. Then file and scrape it smooth.

Необхідні інструменти ({count})

Кувальне горноКувальне горно
Ковальський міхКовальський міх
Кліщі для тиглівКліщі для тиглів
Напилки (ручний напилок)Напилки (ручний напилок)
6

Troubleshooting

Soldering troubleshooting.

Flow

Loading...
7

History and honest limits

From Theophilus, **De Diversis Artibus**, Book III, chapter XXXI, translated by Robert Hendrie (1847) (checked on the archive.org scan essayuponvarious00hend, pp. 241-243). "A third (part)" can be read two ways; both are shown. Melting the alloy before rasping, the tools and the diagram are ours.

Матеріали

5

Необхідні інструменти

10

За цим кресленням виготовляють

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...