Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Thimble: the Pitted Iron Thimble Gilt Inside (Rouy and Berthier, Ure 1839)
Forge

Створено

Forge

4. листопад 2026NO
13
0
0
0
0

Thimble: the Pitted Iron Thimble Gilt Inside (Rouy and Berthier, Ure 1839)

The Paris method of Rouy and Berthier: thin sheet-iron discs, red-hot, punched step by step into a cup through five ever-deeper hollows, then turned, pitted and annealed on the lathe, gilt inside with gold leaf pressed on by a steel mandril, and banded outside with a gold fillet. Variable: closed (pitted round end) or open (no end, for tailors). Source: Andrew Ure, Dictionary of Arts, Manufactures and Mines (1839), 'Thimble'. Picture: a modern pitted thimble (Commons, CC BY-SA 3.0).
Просунутий
Unknown

Інструкції

1

Punch the blanks

Cut sheet iron 1/24 in thick into strips sized for the thimbles. Run them under a punch press to cut discs about 2 in across, left joined by a tail, a dozen to a strip.

Матеріали для цього кроку:

Залізний лист (кований)Залізний лист (кований)1 1/24 in

Необхідні інструменти ({count})

Вирубний пресВирубний прес
2

Sink the cup

Heat the blanks red-hot and lay each on a mandril fitted to its size. Strike the middle with a round-faced punch about as thick as a finger to sink it into the first hollow, then drive it through a block with five hollows of increasing depth until it has the thimble's shape.

Необхідні інструменти ({count})

ГорноГорно
ЩипціЩипці
Невідомий металНевідомий метал
МолотокМолоток
3

Turn and pit on the lathe

Chuck the rough thimble in the lathe, polish the inside, turn the outside, mark the rings for the gold band, and press in the rows of pits with a milling tool.

Необхідні інструменти ({count})

Токарний верстат по металуТокарний верстат по металу
НакаткаНакатка
4

Anneal, gild and band

Anneal and brighten the thimbles. Line each inside with a thin cone of gold leaf, bonded to the iron by the hard pressure of a smooth steel mandril. Turn an annular seat outside, lay a gold fillet in it and press its edges into a fine groove cut on the lathe.

Матеріали для цього кроку:

Сухозлітне золотоСухозлітне золото1 lining
Невідомий металНевідомий метал1 gold fillet

Необхідні інструменти ({count})

ГорноГорно
Оправковий стриженьОправковий стрижень
Токарний верстат по металуТокарний верстат по металу

Матеріали

3

Необхідні інструменти

8

За цим кресленням виготовляють

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...