Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Redditch Steel Sewing Needles: Point, Stamp, Eye, Harden, Scour and Drill (Tomlinson, 1854)
Forge

Створено

Forge

14. листопад 2026NO
11
0
0
0
0

Redditch Steel Sewing Needles: Point, Stamp, Eye, Harden, Scour and Drill (Tomlinson, 1854)

How the Redditch needle mills of the 1850s made steel sewing needles, from Tomlinson's Cyclopaedia of Useful Arts: wire cut in double lengths, pointed on grit stones, stamped and punched for two eyes, split, hardened and tempered blue, then scoured bright for days in rolled canvas bundles with emery and oil.
Просунутий
About two weeks per lot (scouring alone 50-60 hours)

Інструкції

1

Gauge and rates

Завантаження блокнота Jupyter…
2

Read the Cyclopaedia of Useful Arts

"The raw material, as received from Birmingham or Sheffield, consists of soft, clean steel wire."
3

Cut and straighten

Cut soft steel wire into lengths of two needles each, about 3 in (76 mm) for size No. 6. Collect several thousand inside two heavy iron rings, heat them to redness, lay them on an iron plate and roll them back and forth with a smooth file between the rings until the grating sound softens: they are then straight.

Матеріали для цього кроку:

Сталевий дрітСталевий дріт1 штука

Необхідні інструменти ({count})

БокорізиБокорізи
Кувальне горноКувальне горно
Залізна плитаЗалізна плита
Напилки (ручний напилок)Напилки (ручний напилок)
Ковальські кліщіКовальські кліщі
4

Point both ends

Grind both ends on a fast grit stone (10-20 in across, by needle size). Spread the wires in the left hand, hold them with the right and roll them so each forms a true cone. Dip them in water to keep them cool. The dust of grit and steel causes grinder's asthma: he urged a mask and a fan-driven ventilating shaft; wear a dust mask and extract the dust.

Необхідні інструменти ({count})

Точильний кругТочильний круг
Гартівна діжкаГартівна діжка
Протипиловий респіраторПротипиловий респіратор
5

Stamp the eyes

Lay each blank on the iron bed of the stamp (half a die, on a stone block), push it to the stop, and drop the 12 lb hammer with the other half of the die by its foot lever. One blow gives the grooves and a dent for each of the two eyes.

Необхідні інструменти ({count})

Штампувальний молот зі штампамиШтампувальний молот зі штампами
6

Punch the eyes

In a small hand press with two steel points the size of the eye, punch both eyes through. File off the burr from many at once spitted on two fine wires through the eyes, then bend the row back and forth between the spits so it breaks into two rows of single needles. Grip each row in a hand vice and file the heads to shape.

Необхідні інструменти ({count})

Вирубний пресВирубний прес
Напилки (ручний напилок)Напилки (ручний напилок)
Ручний цанговий затискач для сверделРучний цанговий затискач для свердел
7

Straighten soft

Roll each bent needle on a flat steel plate with a smooth steel file turned up at each end; two or three turns straighten it.

Необхідні інструменти ({count})

Залізна плитаЗалізна плита
Напилки (ручний напилок)Напилки (ручний напилок)
8

Harden and temper

Spread the needles thickly on narrow iron plates, heat them to red in the furnace and plunge them into cold water or oil. Dry them, then heat them on an iron plate over a fire, stirring them with small iron shovels until a blue oxide forms, and take them off at once. Roll them on a steel slab to find the bent ones and straighten those with a hammer on a small anvil.

Матеріали для цього кроку:

Машинне мастилоМашинне мастило1 штука

Необхідні інструменти ({count})

Кувальне горноКувальне горно
Залізна плитаЗалізна плита
Гартівна діжкаГартівна діжка
КовадлоКовадло
МолотокМолоток
9

Scour bright

Lay strings across an open wooden tray, a stout canvas on them, and 40,000-50,000 needles lengthwise in it. Sprinkle emery, oil and soft soap, roll it up and wind strong twine round it into a bundle 2-3 ft long and 3-4 in thick. Work it under the weighted slab of a scouring machine, 20-30 strokes a minute, for 50-60 hours (7 or 8 days for the best needles). Every 8 hours renew the canvas, add fresh polishing putty and oil, and wash the needles in soap and water.

Матеріали для цього кроку:

ПарусинаПарусина1 штука
Наждачний порошокНаждачний порошок1 штука
Машинне мастилоМашинне мастило1 штука
МилоМило1 штука
Полірувальний порошокПолірувальний порошок1 штука
Бавовняний шпагатБавовняний шпагат1 штука

Необхідні інструменти ({count})

Машина для відтирання дрібних деталейМашина для відтирання дрібних деталей
10

Head, drill and finish

Turn all heads one way: press a finger wrapped in rag into the heap and the points that stick draw out. Reject broken ones. Anneal the eyes by bringing a red-hot plate near them until dark blue, then countersink and smooth each eye on both sides with a small fast three-sided steel drill. Finish the points on a small turning hone-stone and polish on wooden wheels covered in buff leather with polishing paste.

Матеріали для цього кроку:

Полірувальна пастаПолірувальна паста1 штука

Необхідні інструменти ({count})

Залізна плитаЗалізна плита
Свердлильний верстатСвердлильний верстат
Точильний брусокТочильний брусок
Полірувальний кругПолірувальний круг
11

Troubleshooting

Needle troubleshooting.

Flow

Loading...
12

History and honest limits

From Charles Tomlinson (ed.), **Cyclopaedia of Useful Arts** (1854), vol. II, "Needles" (checked on the archive.org scan cyclopdiaofuse02tomlrich, pp. 321-325). He describes a whole mill; quantities scale down. Metric figures, the dust mask and the tool heads are ours.

Матеріали

8

Необхідні інструменти

17

За цим кресленням виготовляють

Пов'язані креслення

Ці креслення діляться знаннями — техніки, матеріали або принципи

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...