Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
USB-B Cable: Type-A Plug to Type-B Plug, Wired to the USB 2.0 Specification
Ed

Створено

Ed

4. листопад 2026FI
20
0
0
0
0

USB-B Cable: Type-A Plug to Type-B Plug, Wired to the USB 2.0 Specification

A USB-B cable joins a computer (Type-A plug) to a device such as an Arduino board or a printer (Type-B plug). The USB 2.0 Specification (USB Implementers Forum, 2000) fixes the wiring: contact 1 VBUS on the red wire, 2 D- white, 3 D+ green, 4 GND black, and the plug shells joined through the cable's shield. It also sets the cable's build and its limits: a twisted green-white data pair, a red-black power pair, foil and braid shields, no more than 26 ns of delay, and less than 0.6 ohm from shell to shell. This rung works out how long the cable may be, then cuts a 1.5 m shielded cable, solders a Type-A plug to one end and a Type-B plug to the other, and checks every wire with a multimeter. Source: Universal Serial Bus Specification Rev. 2.0, sections 6.4.1, 6.5.2, 6.6, 7.1.16, 7.2.2. Picture: our own drawing.
Середній
About 1 hour

Інструкції

1

How long may it be?

The delay and voltage-drop limits from the specification, and what they allow for each wire size.
2

Cut and strip the cable

Cut 1.5 m of shielded USB cable with a 24 AWG power pair. At each end, slit and remove 20 mm of the PVC jacket with the knife. Comb the braid back over the jacket, trim the foil off and keep the bare drain wire. Strip 3 mm of insulation from the red, black, green and white wires.

Матеріали для цього кроку:

Екранований кабель USBЕкранований кабель USB1.5 m

Необхідні інструменти ({count})

РулеткаРулетка
Будівельний ніжБудівельний ніж
БокорізиБокорізи
Інструмент для знімання ізоляціїІнструмент для знімання ізоляції
Захисні окуляриЗахисні окуляри
3

Solder the Type-A plug

Slide the plug's hood and a 40 mm piece of heat-shrink tubing onto the cable. Tin the wires and solder them to the plug's contacts: 1 red (VBUS), 2 white (D-), 3 green (D+), 4 black (GND). Twist the drain wire into the braid and solder both to the plug's metal shell.

Матеріали для цього кроку:

Вилка USB типу AВилка USB типу A1 штука
Термоусадочна трубкаТермоусадочна трубка40 mm
Дріт припоюДріт припою1 as required

Необхідні інструменти ({count})

ПаяльникПаяльник
Третя рукаТретя рука
4

Solder the Type-B plug

Do the same at the other end with the Type-B plug: 1 red (VBUS), 2 white (D-), 3 green (D+), 4 black (GND), drain wire and braid to the shell. Pin 1 must reach pin 1 at both ends.

Матеріали для цього кроку:

Вилка USB типу BВилка USB типу B1 штука
Термоусадочна трубкаТермоусадочна трубка40 mm
Дріт припоюДріт припою1 as required

Необхідні інструменти ({count})

ПаяльникПаяльник
Третя рукаТретя рука
5

Check every wire

With the multimeter, check that each contact connects to the same contact at the other end and to no other, and that no contact touches a shell. Measure from shell to shell: the specification asks for less than 0.6 ohm.

Необхідні інструменти ({count})

МультиметрМультиметр
6

Close the plugs

Clip the hoods over the plugs, slide the heat-shrink tubing over each joint between hood and cable, and shrink it with the heat gun as a strain relief.

Необхідні інструменти ({count})

ТермофенТермофен
7

History and honest limits

The specification's revision history dates USB 1.0 to 15 January 1996, 1.1 to 23 September 1998 and 2.0, which added high speed, to 27 April 2000. The specification requires a standard detachable cable to end in OVERMOLDED plugs; ours has hand-soldered plugs in hoods, so it is not a compliant cable. We do not measure its 90 ohm impedance or its delay. The 1.5 m length, the 24 AWG power pair and the strip lengths are ours. How the plugs and the cable are made is not covered (unknown heads).

Матеріали

5

Необхідні інструменти

9

За цим кресленням виготовляють

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...