Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Utility Knife: Strip-Made Blades and a Moulded Handle
Emma

Створено

Emma

11. жовтень 2026SE
27
0
0
0
0

Utility Knife: Strip-Made Blades and a Moulded Handle

Utility knife blades are made from a coil of carbon steel strip. A punch press punches the notches along it, the strip is scored across where each blade will break off, and it is coiled again and hardened and tempered, in a vacuum furnace or in line, typically to about 58 Rockwell C. The hard strip is then ground, honed and stropped along one edge, and snapped at each score line into trapezoid blades. Snap-off blades use the same idea: the break comes at the score lines, where the metal is thinnest. The handle that holds the replaceable blade is die-cast metal or moulded plastic.
Просунутий
Continuous (industrial)

Інструкції

1

Punch the strip

Run the carbon steel strip through a punch press to punch the notches at regular spacing.

Матеріали для цього кроку:

Стрічка з вуглецевої сталіСтрічка з вуглецевої сталі10 кг

Необхідні інструменти ({count})

Вирубний пресВирубний прес
2

Score

Score the strip across at each blade's side edge: these lines are where it will later snap.

Необхідні інструменти ({count})

Ролики для надсікання стрічкиРолики для надсікання стрічки
3

Harden and temper

Coil the strip and harden and temper it, to about 58 Rockwell C.

Необхідні інструменти ({count})

Піч для гартування й відпуску стрічкиПіч для гартування й відпуску стрічки
4

Grind the edge

Grind, hone and strop one side of the strip to a straight cutting edge.

Необхідні інструменти ({count})

Лінія заточування й доведення лезЛінія заточування й доведення лез
5

Snap into blades

Snap the strip at each score line into trapezoid blades.
6

Handle

Mould the handle that holds and retracts the blade, here in plastic.

Матеріали для цього кроку:

Гранули ABSГранули ABS0.1 кг

Необхідні інструменти ({count})

Ливарна машинаЛиварна машина

Матеріали

2

Необхідні інструменти

5

За цим кресленням виготовляють

Пов'язані креслення

Ці креслення діляться знаннями — техніки, матеріали або принципи

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...