Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Counter-Turning Cylinder Churn: The Ribbed Cylinder Turns One Way While the Dashers Inside Turn the Other
Buttercup

Створено

Buttercup

11. листопад 2026IE
6
0
0
0
0

Counter-Turning Cylinder Churn: The Ribbed Cylinder Turns One Way While the Dashers Inside Turn the Other

Edwin Ward of New York received US 27,175, dated 14 February 1860, for a churn. A horizontal cylinder with ribs inside turns on bearings while a shaft through it, carrying dashers, turns the other way: one crank drives both, the cylinder through a pair of pinions on a tube round a short fixed shaft and a toothed ring on its head. He reports butter "in from three to five minutes". The patent gives no sizes; every size here is ours.
Просунутий
About 3 days, plus printing

Інструкції

1

One crank, two directions

Завантаження блокнота Jupyter…
2

Dashers turning inside a still barrel, two months before

Rohrer's barrel stands still round the turning dashers. Ward turns the cylinder too, the other way.
3

Read US 27,175

"Now it will readily be seen that whenever rotation is given to the shaft that it and the dashers will traverse in one direction and that the cylinder and slats will traverse in a contrary direction, and that the velocity of the one in relation to that of the other will depend upon the number of teeth and comparative diameter of the pinions and the toothed surface on the head of the cylinder."
4

Print the crown wheel j

Crown wheel, 60 teeth on its face, module 2, with a hub bored 16.4 mm for the shaft. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Файл дизайнуSTLCC0 - Free
5

Print the toothed ring o

Crown ring, 120 teeth on its face, module 2, 258 mm across, to screw to the cylinder's head. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Файл дизайнуSTLCC0 - Free
6

Print the pinions k and n

Spur pinion, 12 teeth, module 2, bored 12.6 mm to turn on the fixed shaft l. Print two. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Файл дизайнуSTLCC0 - Free
7

Cylinder a with ribs d and door p

Cut two hardwood heads 364 mm across from 25 mm board, each with a hub 50 mm across bored 17 mm on the axis, the geared head's hub 38 mm long. Bend 1.5 mm stainless sheet into a shell 360 mm across inside and 450 long, screw it to the heads with silicone sealant, and screw four hardwood ribs 30 x 30 mm, 450 long, inside it a quarter turn apart. Cut a door 140 x 160 mm in the shell, hung on two small hinges and closed with a hook. Screw the printed toothed ring to the geared head's face.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини2 штук
Лист нержавкої сталіЛист нержавкої сталі2 штук
Силіконовий герметикСиліконовий герметик1 штука
Шурупи по деревуШурупи по дереву40 штук
Машинні гвинтиМашинні гвинти8 штук
Меблева карткова завісаМеблева карткова завіса2 штук
Гачок і петляГачок і петля1 штука

Необхідні інструменти ({count})

КомпасКомпас
ЕлектролобзикЕлектролобзик
Ручний фрезерРучний фрезер
Ножиці по металуНожиці по металу
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Набір перових сверделНабір перових свердел
Струбцина з напрямноюСтрубцина з напрямною
Набір викрутокНабір викруток
8

Shaft f, dashers g and crank h

Cut a 16 mm stainless shaft 662 mm long. Screw four hardwood dashers 430 x 122 x 16 mm to hardwood blocks pinned on it, a quarter turn apart, reaching 140 mm from the axis, and pass it through the heads' hubs. Fit the crown wheel on the geared end and a crank 160 mm long with a handle beyond it.

Матеріали для цього кроку:

Пруток із нержавкої сталіПруток із нержавкої сталі1 штука
Дошка з твердої деревиниДошка з твердої деревини1 штука
Шканти з твердої деревиниШканти з твердої деревини1 штука
Столярний клейСтолярний клей1 штука
Shaft CollarShaft Collar2 штук
Філамент PETGФіламент PETG1 штука

Необхідні інструменти ({count})

3D-принтер FDM3D-принтер FDM
Циркулярний верстатЦиркулярний верстат
Ножівка по металуНожівка по металу
Напилки (ручний напилок)Напилки (ручний напилок)
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Наждачний папірНаждачний папір
9

Frame c, bearings b, fixed shaft l and standard m

On a base board stand a post with a hardwood bearing block bored 51 mm for the plain head's hub. At the geared end stand a hardwood standard m, and fix a 12 mm stainless rod l upright in its top, running up into a second bearing block for the geared hub just outside the toothed ring. On l, below the shaft, slide the two pinions joined by a short stainless tube: the upper one meshing the crown wheel j, the lower the toothed ring o. Hold them with collars.

Матеріали для цього кроку:

Хвойний брус 70x70 ммХвойний брус 70x70 мм1 штука
Дошка з твердої деревиниДошка з твердої деревини2 штук
Пруток із нержавкої сталіПруток із нержавкої сталі1 штука
Труба з нержавкої сталіТруба з нержавкої сталі1 штука
Shaft CollarShaft Collar2 штук
Набір шестигранних болтівНабір шестигранних болтів4 штук
Самоконтрувальна гайка з нейлоновим кільцемСамоконтрувальна гайка з нейлоновим кільцем4 штук

Необхідні інструменти ({count})

Циркулярний верстатЦиркулярний верстат
Набір перових сверделНабір перових свердел
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Ножівка по металуНожівка по металу
Розвідний ключРозвідний ключ
РулеткаРулетка
10

The build in 3D

FreeCAD model of this build, the cylinder cut through the middle: the ribs and four dashers, the shaft and crank, the crown wheel and toothed ring facing each other across the upright fixed shaft with its two pinions, the bearings, post and standard on the base.
Файл дизайнуBLENDCC0 - Free
11

Churn

Turn the door uppermost, pour in about 12 litres of heavy cream at about 15 °C, checked with the thermometer, and close it. Turn the crank steadily, timing it: the patent says three to five minutes. When the butter comes, turn the door down over a bowl, let the buttermilk run out, take out the butter, wash it in cold water until it runs clear, salt and weigh it.

Матеріали для цього кроку:

Жирні вершкиЖирні вершки12 l
Крупна морська сільКрупна морська сіль1 штука
ВодаВода1 штука

Необхідні інструменти ({count})

Термометр зі щупом, що лишається в стравіТермометр зі щупом, що лишається в страві
СекундомірСекундомір
Цифрові кухонні вагиЦифрові кухонні ваги
Велика миска з нержавкої сталіВелика миска з нержавкої сталі
12

Troubleshooting

Counter-turning churn troubleshooting.

Flow

Loading...
13

History and honest limits

**Edwin Ward** of New York, US 27,175, 14 February 1860, "Churn". He claimed the horizontal cylinder with ribs and an interior shaft with dashers, made to turn in opposite directions. His bevel pinions and the toothed surface on the head are here printed crown gears and pinions, and his fixed shaft l is upright, carrying the geared end's bearing. The patent gives no sizes; every size here is ours.

Матеріали

19

Необхідні інструменти

20

Файли дизайну

4

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...