Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Water Bath: Copper Tank with Plug-In Heaters and an Air-Tube Thermostat (Lidberg, US 1,397,766, 1921)
Penny

Створено

Penny

3. листопад 2026DK
9
0
0
0
0

Water Bath: Copper Tank with Plug-In Heaters and an Air-Tube Thermostat (Lidberg, US 1,397,766, 1921)

An electric constant-temperature water bath for laboratory and bacteriological work. A copper tank sits in an insulated fibre-board box; two heater tubes and a thermostat tube are soldered through its wall so the heating coils and the switch plug in from outside. A switch adds extra coils to heat the water up quickly; then the thermostat alone holds the set temperature. Perforated trays on adjustable rods hold the tubes or flasks at the depth you choose. Result: a thermostatic water bath that holds its water at a set temperature. Source: T. Lidberg (Chicago Surgical & Electrical Co.), US 1,397,766 (1921). Unknown: sizes, the temperature range, the heater wire. Picture: the patent drawing.
Середній
Unknown

Інструкції

1

Build the insulated tank

Make a rectangular box of fibrous board on four short legs and line it with hair felt or cloth. Set a sheet copper tank inside, its walls a little taller than the box and turned over the top edge as a bead. Make perforated trays of several shelves, each with an upright rod hooked at the top for lifting, and on each rod a sliding clip with a set screw whose end rests on the tank edge, to set how deep the tray hangs. Not given: sizes.

Матеріали для цього кроку:

Невідомий матеріалНевідомий матеріал1 fibrous board box, legs
Невідома тканинаНевідома тканина1 hair felt or cloth lining
Мідний листМідний лист1 tank
Перфорована ситова плитаПерфорована ситова плита1 trays
Невідомий металНевідомий метал1 rods, clips
Машинні гвинтиМашинні гвинти1 штука

Необхідні інструменти ({count})

Ножиці по металуНожиці по металу
ПаяльникПаяльник
Невідомі розміриНевідомі розміри
2

Fit the heater tubes

Solder two watertight tubes across the tank, each closed at its inner end and open outside the wall, and a third for the thermostat. For each heater, wind two coils on a rod held in the tube by an insulating disk and an end head; join one end of each coil to the rod and the others to plates on the head, and cover the terminals with a cap plate. Slide each heater into its tube. Ours: nichrome wire. Not given: the coil ratings.

Матеріали для цього кроку:

Мідна трубаМідна труба3 heater and thermostat tubes
Олов'яно-свинцевий припійОлов'яно-свинцевий припій1 as needed
Ніхромовий дрітНіхромовий дріт1 four coils
Невідомий металНевідомий метал2 rods, plates, caps
Невідомий ізоляційний матеріалНевідомий ізоляційний матеріал1 disks, heads

Необхідні інструменти ({count})

ПаяльникПаяльник
Ножівка по металуНожівка по металу
3

Make the air-tube thermostat

In the closed thermostat tube, mount on an insulating disk a strip carrying a thermostatic bar with a contact at its free end. Facing it, pivot an adjustable bar with its own contact on a bracket in the tube's insulating head, held by a spring against an adjusting screw with a knob outside: turning it sets the temperature at which the contacts open. Bridge the contacts with a condenser to stop sparking. The air in the tube takes the bath's temperature and bends the bar. Ours: a bimetallic strip.

Матеріали для цього кроку:

Біметалева пластинаБіметалева пластина1 thermostatic bar
Невідомий металНевідомий метал1 strip, bar, bracket, contacts, screw
Невідомий ізоляційний матеріалНевідомий ізоляційний матеріал1 disk, head
Набір пружин стискуНабір пружин стиску1 штука
Набір конденсаторівНабір конденсаторів1 spark condenser

Необхідні інструменти ({count})

Набір викрутокНабір викруток
4

Wire and use it

Wire one coil of each heater through the thermostat, and the other coil of each through a hand switch, with a lamp across the supply to show when current flows. To start, close the switch so all four coils heat the water up. Once it is at temperature, open the switch: the thermostat then switches its two coils on and off to hold the bath steady. Lower the trays of tubes or flasks to the depth wanted.

Матеріали для цього кроку:

ТумблерТумблер1 штука
Ламповий патронЛамповий патрон1 штука
Лампа розжаренняЛампа розжарення1 штука
Гнучкий шнур із вилкоюГнучкий шнур із вилкою1 штука

Необхідні інструменти ({count})

Набір викрутокНабір викруток

Матеріали

17

Необхідні інструменти

5

За цим кресленням виготовляють

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...