Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Wedging Table: Plaster-Topped with a Cutting Wire (Binns, 1910)
Woody

Створено

Woody

4. листопад 2026NO
8
0
0
0
0

Wedging Table: Plaster-Topped with a Cutting Wire (Binns, 1910)

The potter's wedging table Binns taught: a strong table with a 30 by 20 in top of two-inch plank, edged to make a trough filled with plaster, and a fine brass wire stretched diagonally from a post on one side for cutting the clay. Clay is cut on the wire and slapped down on the plaster, fifteen or twenty times, until it is even; wet the plaster if it stiffens the clay too fast. Source: C. F. Binns, The Potter's Craft (1910), p. 79. Picture: the book's text.
Початківець
Unknown

Інструкції

1

Make the top

Build a strong table whose top, about 30 by 20 in, is of two-inch plank. Nail a raised edge 2 in high firmly to the sides to form a trough.

Матеріали для цього кроку:

Дошка пиломатеріалуДошка пиломатеріалу1 two-inch plank, about 30 x 20 in
ДошкаДошка1 raised edge, 2 in high
Залізні цвяхиЗалізні цвяхи1 штука

Необхідні інструменти ({count})

Ручна пилкаРучна пилка
МолотокМолоток
2

Pour the plaster

Fill the trough with plaster and let it harden.

Матеріали для цього кроку:

Гіпс будівельнийГіпс будівельний1 штука

Необхідні інструменти ({count})

МолотокМолоток
3

Fit the post and wire

Fasten an upright post in the centre of one side and stretch a fine brass wire from its top to the other side of the table, making a diagonal. The worker stands on the side opposite the post.

Матеріали для цього кроку:

Невідомий матеріалНевідомий матеріал1 upright post, material not given
Тонкий латунний дрітТонкий латунний дріт1 fine brass wire
Залізні цвяхиЗалізні цвяхи1 штука

Необхідні інструменти ({count})

МолотокМолоток
Ручна пилкаРучна пилка

Матеріали

6

Необхідні інструменти

2

За цим кресленням виготовляють

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...