Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Oblique Box-Dasher Churn: A Hollow Slanted Dasher, Open on Two Sides, Churns Fast and Gathers the Butter Inside It Turned Slow
Buttercup

Створено

Buttercup

11. листопад 2026IE
8
0
0
0
0

Oblique Box-Dasher Churn: A Hollow Slanted Dasher, Open on Two Sides, Churns Fast and Gathers the Butter Inside It Turned Slow

Moses D. Wells of Morgantown, Virginia, received US 31,756, dated 19 March 1861, for a churn dasher shaped as a slanted open box: two flat end plates carrying the journals, two curved face pieces with lips at opposite corners, and two open sides. It turns on a horizontal axis in a box whose bottom is curved to its sweep. Turned fast it churns; turned the same way slowly, it gathers the butter inside itself, the lips keeping it from being thrown out, so it lifts out in a lump. The patent gives no sizes; every size here is ours.
Середній
About 2 days

Інструкції

1

Churning fast, gathering slow

Завантаження блокнота Jupyter…
2

A round-bottomed box with a turning dasher, eight months before

Park's box works the butter with pins. Wells's hollow dasher gathers it inside itself.
3

Read US 31,756

"The dasher being hollow, a few slow turns of the same causes the butter to collect within the box so as to be removed in a lump. ... The object of the diagonal lips b', b', is, to gather the butter against, and prevent it from being thrown out of the box in turning it around."
4

Body B with a curved bottom, legs and lid

Glue up two hardwood ends 22 mm thick, 350 mm wide and 320 tall. On each draw the inside: a 300 mm half circle with its centre 160 mm up, and straight sides rising 150 mm above the centre to the top. Rout a groove 1.6 mm wide and 8 deep on that line. Cut a slot 16.6 mm wide down from the top edge to the centre, rounded at its foot, as the journal bearing, and a hardwood keeper that fills the slot above the journal. Bend a 1.5 mm stainless sheet 416 mm long into a U to fit the line, set it in both grooves with silicone sealant, and screw hardwood sides 22 mm thick outside its straight parts. Screw four hardwood legs 40 x 40 mm, 390 long, to the ends, splayed out. Cut a hardwood lid 444 x 350 x 22 mm, notched over the keepers, with a 25 mm air opening o.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини4 штук
Лист нержавкої сталіЛист нержавкої сталі1 штука
Силіконовий герметикСиліконовий герметик1 штука
Столярний клейСтолярний клей1 штука
Шурупи по деревуШурупи по дереву30 штук

Необхідні інструменти ({count})

Циркулярний верстатЦиркулярний верстат
КомпасКомпас
ЕлектролобзикЕлектролобзик
Ручний фрезерРучний фрезер
Набір стамесок по деревуНабір стамесок по дереву
Гумовий молотокГумовий молоток
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Набір перових сверделНабір перових свердел
Струбцина з напрямноюСтрубцина з напрямною
Набір викрутокНабір викруток
РулеткаРулетка
5

Print the end plates a (two)

An end plate of the dasher: 15 mm thick, the slanted outline of Fig. 1 with curved top and bottom edges, a 50 mm boss at the centre. Print two; drill each 16 mm at the centre for a journal. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Файл дизайнуSTLCC0 - Free
6

Dasher D: end plates a, face pieces b with lips b', journals

Cut two strips of 1.5 mm stainless sheet 360 mm long, each 160 mm wide; bend each to a curve of about 300 mm radius following the end plates' curved edges, with a 20 mm lip b' at one long edge turned on round the corner. Screw them to the end plates' curved edges, the lips at diagonally opposite corners, leaving the two slanted sides open. Push a 16 mm stainless journal into each end plate's boss and pin it: one 40 mm long, the other 90 mm for the crank. Lay the journals in the slots and drop in the keepers. Pin a crank of mild steel flat bar, 120 mm throw, with a hardwood handle, on the long journal.

Матеріали для цього кроку:

Філамент PETGФіламент PETG1 штука
Лист нержавкої сталіЛист нержавкої сталі1 штука
Шурупи по деревуШурупи по дереву16 штук
Пруток із нержавкої сталіПруток із нержавкої сталі1 штука
ШплінтШплінт3 штук
Смуга з маловуглецевої сталіСмуга з маловуглецевої сталі1 штука
Шканти з твердої деревиниШканти з твердої деревини1 штука

Необхідні інструменти ({count})

3D-принтер FDM3D-принтер FDM
Ножиці по металуНожиці по металу
Гумовий молотокГумовий молоток
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Ножівка по металуНожівка по металу
Напилки (ручний напилок)Напилки (ручний напилок)
Слюсарні лещатаСлюсарні лещата
Набір викрутокНабір викруток
7

The build in 3D

FreeCAD model of this build, cut open: the round stainless bottom in grooved ends with slotted bearings and keepers, the legs and lid with its air opening, and the slanted hollow dasher with its curved, lipped face pieces and crank.
Файл дизайнуBLENDCC0 - Free
8

Churn and gather

Pour about 10 litres of heavy cream at about 15 °C, checked with the thermometer, into the box, so it stands below the axis, and put on the lid. Turn the crank briskly, timing it. When the butter comes, turn the same way slowly for a few turns until it gathers inside the dasher. Lift off the lid and keepers, lift the dasher out by its journals, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

Матеріали для цього кроку:

Жирні вершкиЖирні вершки10 l
Крупна морська сільКрупна морська сіль1 штука
ВодаВода1 штука

Необхідні інструменти ({count})

Термометр зі щупом, що лишається в стравіТермометр зі щупом, що лишається в страві
СекундомірСекундомір
Цифрові кухонні вагиЦифрові кухонні ваги
Велика миска з нержавкої сталіВелика миска з нержавкої сталі
9

Troubleshooting

Box-dasher churn troubleshooting.

Flow

Loading...
10

History and honest limits

**Moses D. Wells** of Morgantown, Monongalia County, Virginia (now West Virginia), US 31,756, 19 March 1861, "Churn-Dasher". He claimed "the oblique box dasher D constructed and operating substantially as set forth, that is to say, with two flat sides, two curved sides, and two open sides, and turned in the same direction for churning, and for gathering the butter, but at various velocities". He says only that the journals have "suitable connections to facilitate the removal of the dasher"; ours lie in open slots under keepers. The patent gives no sizes; every size here is ours.

Матеріали

13

Необхідні інструменти

21

Файли дизайну

2

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...