Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО

Fluted-Shoulder Spade Bits With Spurs: Flutes Along the Shoulders, Stopped by Corner Spurs (Williams & Thackston, 1987)
A. Graves Williams III and Ronald L. Thackston of Ohio received US 4,682,917, dated 28 July 1987, for The Irwin Company. They kept Robinson's flutes on the point and added a flute along each shoulder's cutting edge, joining the point flute. Each flute stops just short of the outside, closed by a sharp spur at the corner whose inner edge slopes into it. The spur scores the rim of the hole. In oak their bits bored up to twice as fast as Robinson's, and left a clean exit instead of a splintered one.
We forge three of their test sizes, 5/8, 7/8 and 1 inch. The patent gives the angles; the other sizes are ours.
Просунутий
About 1 day
Інструкції
1
1
Their tests
Their tests
Завантаження блокнота Jupyter…
2
2
Read US 4,682,917
Read US 4,682,917
"If the flutes are 'stopped', that is, if they do not extend or 'open' to the respective outer sides of the blade, and if cutting spurs are provided at the outer corners of the shoulders so that the spurs 'close' the flutes, then this splitting is virtually eliminated and cutting proceeds more smoothly."
3
3
Forge the blades
Forge the blades
Cut three 170 mm lengths of 10 mm octagonal tool steel. Heat 50 mm of one end to a bright orange in the forge and flatten it on the anvil to about 3 mm thick, centred on the bar. Hammer across it with the peen to spread it wider than the bit, about 2 mm over its size: 18, 24 and 27 mm. Draw the neck down smoothly where the blade meets the bar and keep the blade in line with it. Reheat as soon as the colour fades to red. Finally heat each one to a cherry red and let it cool slowly in the air, to soften it for filing.
Матеріали для цього кроку:
Восьмигранник з інструментальної сталі3 штукНеобхідні інструменти ({count})
Ножівка по металу
Слюсарні лещата
Горно
Ковадло
Ковальський молот
Ковальські кліщі
Зварювальні рукавиці
Захисні окуляри4
4
Print the grinding template
Print the grinding template
Full-size A4 template: the outlines of the 5/8, 7/8 and 1 inch bits with square shoulders and corner spurs, the joined point and shoulder flutes on one face, and the hanging hole. Print at 100 %; its 50 mm bar must measure 50 mm.
5
5
Grind the outline
Grind the outline
Glue each bit's outline from the template on its blade, centred on the bar. Grind to the lines on the bench grinder, dipping the steel in water often: the two sides parallel, the shoulders square across, the point in the middle. Grind the blade's two faces flat and parallel to 2.5 mm. Grind three flats on the end of the shank, a third of the way round from each other, 20 mm long, for the chuck's jaws. Leave a spur 2 mm wide and 2 mm high at each outer corner of the shoulders. Drill a 3 mm hole at the template's circle.
Необхідні інструменти ({count})
Струменевий принтер
Клей
Настільний точильний станок
Гартівна діжка
Вода
Набір напилків
Слюсарні лещата
Цифровий штангенциркуль 6 дюймів
Захисні окуляри6
6
Bevel the edges and file the flutes
Bevel the edges and file the flutes
Bevel the outer sides and the shoulders' cutting edges slightly, so each edge meets its leading face at about 86 degrees. On the face towards you, file the point flute along the point's left edge with the 3 mm round needle file, 0.3 mm deep. Then file the shoulder flute with the three-square needle file along the left shoulder, right behind its cutting edge and square to the bit's axis, from the point flute to the spur, and stop there. Bevel the spur's inner edge into the flute so the spur has a sharp outer edge. Turn the bit over and do the same along that face's left edge and shoulder.
Необхідні інструменти ({count})
Настільний точильний станок
Гартівна діжка
Вода
Слюсарні лещата
Набір надфілів
Цифровий штангенциркуль 6 дюймів7
7
Harden and temper
Harden and temper
Heat the blade and the neck evenly to a cherry red, until a magnet no longer sticks to it, and quench it straight down in water, moving it up and down. Rub the faces bright with a stone. Heat the shank gently 30 mm behind the blade and watch the colours run down; quench again as soon as a dark straw colour reaches the shoulders and the point. Do the other two.
Необхідні інструменти ({count})
Горно
Ковальські кліщі
Невеликий магніт
Гартівна діжка
Вода
Точильний камінь
Зварювальні рукавиці
Захисні окуляри8
8
Sharpen and test
Sharpen and test
Hone the cutting edges on the shoulders and the point with the stone, keeping their angles, and take the burr off. Chuck a bit by its flats and bore a scrap of hardwood: it should start on the point without wandering, cut two clean shavings from the shoulders and leave a round hole of its own size; check it with the caliper.
Необхідні інструменти ({count})
Точильний камінь
Акумуляторний дриль
Дошка з твердої деревини
Цифровий штангенциркуль 6 дюймів
Захисні окуляри9
9
Troubleshooting
Troubleshooting
Spade bit troubleshooting.
Flow
Loading...
10
10
History and honest limits
History and honest limits
**A. Graves Williams III**, Wilmington, and **Ronald L. Thackston**, Hillsboro, Ohio, assignors to The Irwin Company, US 4,682,917, dated 28 July 1987, filed 24 January 1986. They claimed "cutting spurs projecting forwardly from the shoulders" with sharp outer edges, and shoulder flutes from the point flutes towards the spurs, "terminating at the spurs so that the shoulder flutes do not extend across the spurs to the outer sides of the blades". They prefer the flutes forged and the flute wall at about 68 degrees; we file them, with a three-square file at 60 degrees, inside their "less than about 78". Their shank has a hexagonal end; ours is octagonal tool steel with three ground flats. They give no heat treatment or spur size; those are ours.
Матеріали
1- Заповнювач
Необхідні інструменти
20- Заповнювач
- Заповнювач
- Заповнювач
- Заповнювач
- Заповнювач
- Заповнювач
- Заповнювач
- Заповнювач
- Заповнювач
- Заповнювач
- Заповнювач
- Заповнювач
- Заповнювач
- Заповнювач
- Заповнювач
- Заповнювач
- Заповнювач
- Заповнювач
- 1 vendor sell this, none ship to you yetЗаповнювач
- Заповнювач
Файли дизайну
1За цим кресленням виготовляють
Пов'язані креслення
Ці креслення діляться знаннями — техніки, матеріали або принципи
CC0 Суспільне надбання
Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.
Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.


