Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Winding Sticks: a Pair of Parallel Mahogany Strips Planed Together (Work, 1889)
Woody

Створено

Woody

8. листопад 2026NO
7
0
0
0
0

Winding Sticks: a Pair of Parallel Mahogany Strips Planed Together (Work, 1889)

Two parallel wooden strips laid across a board to show twist (winding). Carpenters and joiners made their straightedges in pairs as winding strips: if two parallel strips still meet edge to edge when their edges and ends are swapped, three edges have been checked against each other and the strips are true. Straight-grained mahogany is used for strips under three feet. The two are planed together, then tried against each other and reversed until no difference shows. Source: J. H., 'Home-Made Tools', Work, 26 October 1889, pp. 499-500. Picture: Figs. 26-27.
Середній
Unknown (the stuff is left to stand for days or weeks first)

Інструкції

1

Read the source

"Carpenters, joiners, pattern makers, and cabinet makers usually make their straightedges in pairs as 'winding strips;' and it is clear that if two winding strips are in the first place parallel, and then coincident when the positions of edges and ends are changed, there is obtained really the contact of three edges." (Work, 26 October 1889.)
2

Rough out and let stand

Rough out two strips of well-seasoned, straight-grained mahogany (for strips under three feet; long ones are made of yellow pine). Jack them over and let them stand for a few days or even weeks, because fresh-cut strips curve and warp. Length, width and thickness are not given (unknown).

Матеріали для цього кроку:

Смуга твердої деревиниСмуга твердої деревини2 mahogany strips

Необхідні інструменти ({count})

Ручний рубанокРучний рубанок
Невідомі розміриНевідомі розміри
3

Plane them together

Plane both to gauged thickness and width and square the ends. Screw the two side by side, then finish the edges together with a trying plane sharpened keenly and set very fine. Gauge to width with a fine-toothed gauge, check them parallel with calipers, and keep the edges square to the faces with a try square.

Необхідні інструменти ({count})

Шурупи по деревуШурупи по дереву
Ручний рубанокРучний рубанок
Розмічальний рейсмусРозмічальний рейсмус
ШтангенциркульШтангенциркуль
Столярний косинецьСтолярний косинець
4

Test the edges

To test an edge without a straightedge, lay the strip on a board, scribe a fine line along the edge, turn the strip over and bring the opposite edge to the line: any error shows at twice its size. Plane off the high parts, still checking with calipers and square.

Необхідні інструменти ({count})

Дошка з твердої деревиниДошка з твердої деревини
Розмічальний ніжРозмічальний ніж
Ручний рубанокРучний рубанок
ШтангенциркульШтангенциркуль
Столярний косинецьСтолярний косинець
5

Unfasten and try them against each other

Take the screws out. Lay the strips edge to edge by opposite edges in turn, then change ends and try the opposite edges again, correcting with the trying plane until no difference shows (woodworkers test by chalking the edges and laying them together). Most of the work should already have been done while they were joined.

Необхідні інструменти ({count})

Розмічальна крейдаРозмічальна крейда
Ручний рубанокРучний рубанок
ШтангенциркульШтангенциркуль
Столярний косинецьСтолярний косинець
6

Varnish the faces

Protect the broad faces and the ends with shellac varnish, but not the edges, which are chalked in use. Chalking wears the edges hollow and wood always warps a little, so re-correct winding strips every few months, and keep them for testing winding only.

Матеріали для цього кроку:

Шелаковий лакШелаковий лак1 faces and ends

Матеріали

2

Необхідні інструменти

9

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...