Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Wire-Arc Spray Gun: Two Crossed Wires, a Vibrating Arc and an Air Blast (Schoop, US 1,133,508, 1915)
Forge

Створено

Forge

3. листопад 2026NO
11
0
0
0
0

Wire-Arc Spray Gun: Two Crossed Wires, a Vibrating Arc and an Air Blast (Schoop, US 1,133,508, 1915)

The first wire-arc metal sprayer. Two metal wires are pushed through iron tubes until their tips cross. Current through the wires also runs an electromagnet that pulls one tube back, so a small arc springs between the tips and melts them; a jet of air blows the molten metal off as a fine spray and puts the arc out, the magnet lets go, the wires touch again, and the cycle repeats very fast. Result: a continuous spray of molten metal for coating a surface. Source: M. U. Schoop, US 1,133,508 (1915). Unknown: the wire metals and sizes, the coil, the air pressure. Picture: the patent drawing.
Просунутий
Unknown

Інструкції

1

Make the feed tubes and rolls

Make two feed tubes ending in nozzles, preferably of iron. For each, mount a pair of feed rolls in a frame to push a wire through the tube. Set the tubes at about 90° to each other so the wires cross as they come out, the nozzles only a few millimetres apart. Mount one tube on an elastic support so it can move a little. Not given: sizes, the roll drive (the air blast may drive a small turbine for it).

Матеріали для цього кроку:

Залізна трубкаЗалізна трубка2 feed tubes
Невідомий металНевідомий метал1 rolls, frames
Листова ресораЛистова ресора1 elastic support

Необхідні інструменти ({count})

Токарний верстат по металуТокарний верстат по металу
Невідомі розміриНевідомі розміри
2

Fit the electromagnet

Wind an electromagnet beside the springing tube, so the tube is its armature. Wire the coil into the same circuit as the two tubes and wires, positive to one tube and negative to the other. When current flows the magnet pulls the tube aside and draws its wire slightly back from the other. Ours: enamelled copper wire for the coil. Not given: the coil.

Матеріали для цього кроку:

Мідний дріт в емалевій ізоляціїМідний дріт в емалевій ізоляції1 coil
Невідомий металНевідомий метал1 magnet core
Мідний дрітМідний дріт1 circuit leads

Необхідні інструменти ({count})

Набір викрутокНабір викруток
3

Fit the air blast

Aim a blast pipe at the point where the wires cross, either close to it or 20-30 mm away, whichever sprays best for the metal. Feed it with compressed air or another gas. Not given: the pressure.

Матеріали для цього кроку:

Повітряне соплоПовітряне сопло1 штука
ПневмошлангПневмошланг1 штука

Необхідні інструменти ({count})

Промисловий повітряний компресорПромисловий повітряний компресор
Розвідний ключРозвідний ключ
4

Spray

Load a wire of the coating metal in each tube and feed them until they touch. Switch on the current, generally 40 to 75 volts depending on the metal and wire thickness, and the air. The magnet pulls the wires apart, an arc melts their tips, the air blows the melt away as spray and snuffs the arc, the magnet releases, and the cycle repeats very rapidly. The positive wire burns faster, so feed it faster or use a thicker wire; match the feed to the melting. Hold the work in the spray. Without the vibration the arc flickers and the wires may weld together.

Необхідні інструменти ({count})

Джерело живлення постійного струмуДжерело живлення постійного струму
Промисловий повітряний компресорПромисловий повітряний компресор
Невідомий металНевідомий метал

Матеріали

7

Необхідні інструменти

7

За цим кресленням виготовляють

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...