Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Workbench: a Pine Bench with a Laminated Maple Top and Vise (Boy Mechanic, 1913)
Woody

Створено

Woody

4. листопад 2026NO
7
0
0
0
0

Workbench: a Pine Bench with a Laminated Maple Top and Vise (Boy Mechanic, 1913)

The same pine bench with a harder top: 14 maple strips set on edge, glued and screwed together, with a back board, a tool rack and a wooden vise on an iron bench screw. Source: C. E. McKinney, Jr., 'Homemade Workbench', The Boy Mechanic, Book 1 (1913), pp. 442-443. Picture: Figs. 1-3 of the book.
Середній
Unknown

Інструкції

1

Make the two leg frames

Cut four 2 x 4 in pine legs 23 in long with a tenon on each end 1/2 in thick, 3 1/2 in wide and 1 1/2 in long (Fig. 1, A and B). Cut four crosspieces of the same stock 20 in long, mortised in the narrow edge 1 1/4 in from each end, and slope their corners from the leg out to the middle. Fit each pair of legs to a pair of crosspieces to make the two supports.

Матеріали для цього кроку:

Сосновий пиломатеріалСосновий пиломатеріал1 2 x 4 in: legs, crosspieces

Необхідні інструменти ({count})

Ручна пилкаРучна пилка
Долото для гніздДолото для гнізд
МолотокМолоток
2

Brace them together

Join the supports with two 2 x 4 in braces 24 in long, ends sawn square. Bore through each leg and 4 in into the centre of each brace end, bore an intersecting hole on the back of each brace for the nut, and draw each joint tight with a 3/8 x 6 in bolt (Fig. 2, J). A cross brace on the back stops rocking when planing.

Матеріали для цього кроку:

Сосновий пиломатеріалСосновий пиломатеріал1 2 x 4 in: braces
Болт із півкруглою головкоюБолт із півкруглою головкою4 3/8 x 6 in

Необхідні інструменти ({count})

Ручна пилкаРучна пилка
Коловорот із перкоюКоловорот із перкою
Розвідний ключРозвідний ключ
3

Build up the maple top

Make the main top M of 14 maple strips 7/8 in thick, 2 in wide and 3 1/2 ft long, set on edge, each glued and screwed to the next, all with the grain one way so it planes smooth. Rabbet its back edge 1/2 in to take a back board N of the same length, 8 1/2 in wide and 7/8 in thick. Screw the top to the top crosspieces with long screws.

Матеріали для цього кроку:

Невідомий матеріалНевідомий матеріал14 maple strips 7/8 x 2 in x 3 1/2 ft
Столярний клейСтолярний клей1 штука
Соснова дошкаСоснова дошка1 back board
Шурупи по деревуШурупи по дереву1 штука

Необхідні інструменти ({count})

Ручна пилкаРучна пилка
Обдирний стругОбдирний струг
Викрутка пласкаВикрутка пласка
4

Add the tool rack

Nail a board E 10 in wide to the back of the bench and fasten a 2 1/2 in board F on top of it at right angles; both 7/8 in thick and 3 1/2 ft long. Bore holes or cut notches in F to hold tools.

Матеріали для цього кроку:

Соснова дошкаСоснова дошка2 7/8 in, 3 1/2 ft
ЦвяхиЦвяхи1 штука

Необхідні інструменти ({count})

Коловорот із перкоюКоловорот із перкою
Ручна пилкаРучна пилка
МолотокМолоток
5

Fit the vise

Fasten an iron bench screw in a 2 x 6 in block 12 in long. Mortise two guide rails 7/8 x 1 1/2 in and 20 in long into the block; they slide in mortises in a 2 x 4 piece L bolted under the top, which holds the bench-screw nut between the two mortises. Nail L to a top crosspiece and to a 2 x 4 piece P bolted under the top at the end (Fig. 3).

Матеріали для цього кроку:

Сосновий пиломатеріалСосновий пиломатеріал1 2 x 6 block, 2 x 4 pieces, guide rails
Верстатний гвинт для різьблення по деревуВерстатний гвинт для різьблення по дереву1 штука
Болт із півкруглою головкоюБолт із півкруглою головкою1 for L and P
ЦвяхиЦвяхи1 штука

Необхідні інструменти ({count})

Ручна пилкаРучна пилка
Долото для гніздДолото для гнізд
Коловорот із перкоюКоловорот із перкою
Розвідний ключРозвідний ключ
МолотокМолоток

Матеріали

8

Необхідні інструменти

7

За цим кресленням виготовляють

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...