Collaboration
ART
BEAUTY & WELLNESS
CRAFT
CULTURE & HISTORY
ENTERTAINMENT
ENVIRONMENT
FOOD & DRINKS
REVERSE ENGINEERING
SCIENCES
SPORTS
TECHNOLOGY
WEARABLES
Chinese Dragon Kite: Bamboo-Ring Head With Revolving Eyes and 20 Sections on a Seine-Twine Harness (Boy Mechanic, 1919)
Spartan

Created by

Spartan

13. November 2026NO
7
0
0
0
0

Chinese Dragon Kite: Bamboo-Ring Head With Revolving Eyes and 20 Sections on a Seine-Twine Harness (Boy Mechanic, 1919)

C. M. Miller's dragon kite from The Boy Mechanic, Book 3 (1919): a 12 in bamboo-ring head with horns and two paper eyes that spin in the wind, followed by up to 20 round section kites, each with a 36 in balancer stick, tied 30 in apart on three cords of seine twine. Twenty sections make a kite about 50 ft long.
Advanced
Several days

Instructions

1

Strip lengths and kite length

Loading Jupyter Notebook...
2

Read The Boy Mechanic, Book 3

"Dragon kites are made as hideous as the maker can possibly conceive, and while the one to be considered is no beauty, it is more droll than fierce-looking."
3

Split and pare the bamboo

Split bamboo into strips about 3/16 in wide and pare them to less than 1/16 in thick for the head's inner ring A. To bend a strip to a sharp angle, heat it over a candle flame until it gives under pressure, bend it, and it keeps its shape when cold.

Materials for this step:

Bamboo PolesBamboo Poles1 piece

Tools needed:

Steel Pocket KnifeSteel Pocket Knife
CandleCandle
4

Frame the head

Make ring A 12 in across from a strip about 38 in long, lapping the ends and winding them with linen thread (or with wet pasted strips of rice paper about 1/2 in wide, which bind as they dry). Lash two crosspieces B and C of the same stock 3-1/2 in apart, parallel and equally spaced from the centre, their ends bent sharply and lashed inside the ring. Lash two eye rings D and E, 3-1/2 in across, between them, shaped round a 3-1/2 in cylinder so they are true. Lash stiffeners F and G, 1/16 by 1/8 by 20 in, across the back. Add outer ring H, 3 in outside A (18 in across), of 1/8 in strip under 1/16 in thick, in two pieces if needed, and the short pieces J and K between the rings. Lash the horn supports, 1/8 in wide, to the upper crosspiece and both rings, with L and M halfway between the ends of F and G and radiating from the centre of A, and N and O pointing at the eye-ring centres (Fig. 2).

Materials for this step:

Bamboo PolesBamboo Poles1 piece
Linen ThreadLinen Thread1 piece

Tools needed:

Steel Pocket KnifeSteel Pocket Knife
CandleCandle
Tape MeasureTape Measure
ScissorsScissors
5

Cover and paint the head

Cover only the inside of ring A, the horns and the ears with Chinese rice paper, stretched tight with no bagging, leaving the eye rings open. Put the rings on the horns and stick ends, 1/2 to 2 in across, cut from stiff paper (larger ones of bamboo). Shade with a brush and water colours, leaving the face white or tinting it; leave the horns white and colour the tongue red (Fig. 1).

Materials for this step:

Rice PaperRice Paper1 piece
Wheat PasteWheat Paste1 piece
Card StockCard Stock1 piece
Watercolour PaintWatercolour Paint1 piece

Tools needed:

Glue BrushGlue Brush
Artist Brush SetArtist Brush Set
ScissorsScissors
6

Make the revolving eyes

Pare bamboo to 1/32 in and form each eye into a true ring 3-1/4 in across. Pass a wire axle exactly on a diameter through the eye ring and through its socket ring D or E, with a glass bead on the wire each side between the two rings; fix the wire to the eye ring with a strip of paper wrapped tight and pasted. Cover each side halfway with rice paper, the front upper half and the back lower half, so the wind turns the eye. Blacken the front upper half and paste a round pupil between the halves so it shows on both sides (Figs. 3, 4).

Materials for this step:

Bamboo PolesBamboo Poles1 piece
Iron WireIron Wire1 piece
Glass BeadsGlass Beads4 pieces
Rice PaperRice Paper1 piece
Wheat PasteWheat Paste1 piece
Watercolour PaintWatercolour Paint1 piece

Tools needed:

Steel Pocket KnifeSteel Pocket Knife
Flat-Nose PliersFlat-Nose Pliers
ScissorsScissors
Artist Brush SetArtist Brush Set
7

Make the section kites

For each section make a 12 in ring of bamboo 1/8 in wide and 1/16 in thick and cover it tight like the head. Lash on a balancer stick 36 in long, small, light and well balanced, at about the place of cross-stick F, with tufts of tissue paper or feathers at its tips. Colour the discs as you like; give the last section's balancer streamers of light cloth (Figs. 5, 6). Sections may instead be 9 in with 30 in balancers, but uniform sections are better and easier.

Materials for this step:

Bamboo PolesBamboo Poles1 piece
Linen ThreadLinen Thread1 piece
Rice PaperRice Paper1 piece
Wheat PasteWheat Paste1 piece
Tissue PaperTissue Paper1 piece
FeathersFeathers1 piece
Cotton ClothCotton Cloth1 piece
Watercolour PaintWatercolour Paint1 piece

Tools needed:

Steel Pocket KnifeSteel Pocket Knife
CandleCandle
ScissorsScissors
Artist Brush SetArtist Brush Set
8

Tie the harness and bridle

Cut three cords of six-ply hard-twisted seine twine as long as the kite plus the knots. Fasten the head to a wall, tie the three cords to it at T, U and V (Fig. 2), and tie each section at the matching points exactly 30 in from the last (Fig. 7). Tie a three-string bridle to the head at T, U and V, the lower string longer than the two upper ones so the head, and with it every section, leans to the wind. A ball balancer of bamboo strips may hang from the head (Fig. 8).

Materials for this step:

Seine TwineSeine Twine1 piece
Kite StringKite String1 piece
Bamboo PolesBamboo Poles1 piece

Tools needed:

Tape MeasureTape Measure
ScissorsScissors
9

Flying and troubleshooting

Dragon kite flying.

Flow

Loading...
10

History and honest limits

From "How to Make Combined Kites, Part I: A Dragon Kite" by C. M. Miller, in **The Boy Mechanic, Book 3**, Popular Mechanics, 1919 (Project Gutenberg 71856; checked on the archive.org scan boymechanic0003unse, pp. 145-148). He gives no bridle lengths and no line size beyond "a strong cord". Fig. 2 also marks 5 in at the horn tip and 1 in where F passes ring H. The tools and metric figures are ours.

Materials

13

Tools Required

7

This blueprint makes

Related Blueprints

These blueprints share knowledge with this one โ€” techniques, materials, or principles that connect them in the learning graph.

CC0 Public Domain

This blueprint is released under CC0. You are free to copy, modify, distribute, and use this work for any purpose, without asking permission.

Support the Maker by purchasing products through their Blueprint where they earn a Maker Commission set by Vendors, or create a new iteration of this Blueprint and include it as a connection in your own Blueprint to share revenue.

Discussion

(0)

Log in to join the discussion

Loading comments...