Collaboration
ART
BEAUTY & WELLNESS
CRAFT
CULTURE & HISTORY
ENTERTAINMENT
ENVIRONMENT
FOOD & DRINKS
REVERSE ENGINEERING
SCIENCES
SPORTS
TECHNOLOGY
WEARABLES
Self-Watering Plant Station with ESP32 and OLED
Ed

Created by

Ed

16. November 2026FI
1
0
0
0
0

Self-Watering Plant Station with ESP32 and OLED

A watering unit that stands next to one houseplant. It has a printed water tank, and a lid on the tank carries the electronics box. An ESP32 reads a capacitive soil-moisture probe in the pot. When the soil is dry, it runs a small 5 V submersible pump in the tank through a logic-level MOSFET, and water goes up a silicone tube to a printed drip stake. A float switch in the tank blocks the pump when the water is low. A 0.96 in OLED shows soil moisture %, tank OK/LOW and pump state. Power comes from a 5 V USB-C adapter.

Instructions

1

Circuit board

Loading KiCanvas viewer...

Professional PCB Design Viewer

2

Schematic

Loading KiCanvas viewer...

Professional PCB Design Viewer

3

Print the enclosure base

Design FileSTL69.0 KBCC0 - Free
4

Print the enclosure lid

Design FileSTL3.2 KBCC0 - Free
5

Print the water tank

Design FileSTL1.4 KBCC0 - Free
6

Print the tank lid

Design FileSTL30.8 KBCC0 - Free
7

Print the drip stake

Design FileSTL53.3 KBCC0 - Free
8

Firmware

firmware.inoarduino
// Self-watering controller - ESP32 DevKit (38-pin)
// Soil sensor AOUT -> GPIO34 (ADC1), float switch -> GPIO27 (internal pull-up, other side GND),
// pump MOSFET gate (via 330R) -> GPIO26, SSD1306 128x64 OLED on I2C (SDA 21, SCL 22, addr 0x3C).
// No external libraries required: a tiny SSD1306 driver and 5x7 font are included below.

#include <Wire.h>

// ---------------- user settings ----------------
const int PIN_SOIL  = 34;
const int PIN_FLOAT = 27;
const int PIN_PUMP  = 26;
const uint8_t OLED_ADDR = 0x3C;

// Float switch wiring: true = contact CLOSED when there is enough water (recommended, fail-safe:
// a broken wire reads as LOW tank and blocks the pump). Set false if your switch closes when empty.
const bool FLOAT_CLOSED_MEANS_OK = true;

// Soil sensor calibration (raw 12-bit ADC). Measure your sensor in dry air and in a glass of water.
const int RAW_DRY = 3000;
const int RAW_WET = 1300;

const int  START_BELOW_PCT   = 35;     // start watering below this moisture
const int  STOP_ABOVE_PCT    = 45;     // stop watering at/above this moisture
const unsigned long PUMP_MAX_MS  = 5000;   // max run per watering burst
const unsigned long SOAK_MS      = 60000;  // wait after a burst so water can soak in
const unsigned long TANK_DEBOUNCE_MS = 500;

// ---------------- SSD1306 driver ----------------
uint8_t fb[1024];

void oledCmd(uint8_t c) {
  Wire.beginTransmission(OLED_ADDR);
  Wire.write(0x00);
  Wire.write(c);
  Wire.endTransmission();
}

void oledInit() {
  const uint8_t init[] = {0xAE, 0xD5, 0x80, 0xA8, 0x3F, 0xD3, 0x00, 0x40, 0x8D, 0x14,
                          0x20, 0x00, 0xA1, 0xC8, 0xDA, 0x12, 0x81, 0xCF, 0xD9, 0xF1,
                          0xDB, 0x40, 0xA4, 0xA6, 0xAF};
  for (uint8_t i = 0; i < sizeof(init); i++) oledCmd(init[i]);
}

void oledShow() {
  oledCmd(0x21); oledCmd(0); oledCmd(127);
  oledCmd(0x22); oledCmd(0); oledCmd(7);
  for (int i = 0; i < 1024; i += 16) {
    Wire.beginTransmission(OLED_ADDR);
    Wire.write(0x40);
    Wire.write(&fb[i], 16);
    Wire.endTransmission();
  }
}

// 5x7 font, columns LSB = top. Only the characters used.
struct Glyph { char c; uint8_t d[5]; };
const Glyph FONT[] = {
  {' ', {0x00,0x00,0x00,0x00,0x00}}, {'%', {0x23,0x13,0x08,0x64,0x62}},
  {'-', {0x08,0x08,0x08,0x08,0x08}}, {'.', {0x00,0x60,0x60,0x00,0x00}},
  {'/', {0x20,0x10,0x08,0x04,0x02}}, {':', {0x00,0x36,0x36,0x00,0x00}},
  {'!', {0x00,0x00,0x5F,0x00,0x00}},
  {'0', {0x3E,0x51,0x49,0x45,0x3E}}, {'1', {0x00,0x42,0x7F,0x40,0x00}},
  {'2', {0x42,0x61,0x51,0x49,0x46}}, {'3', {0x21,0x41,0x45,0x4B,0x31}},
  {'4', {0x18,0x14,0x12,0x7F,0x10}}, {'5', {0x27,0x45,0x45,0x45,0x39}},
  {'6', {0x3C,0x4A,0x49,0x49,0x30}}, {'7', {0x01,0x71,0x09,0x05,0x03}},
  {'8', {0x36,0x49,0x49,0x49,0x36}}, {'9', {0x06,0x49,0x49,0x29,0x1E}},
  {'A', {0x7E,0x11,0x11,0x11,0x7E}}, {'B', {0x7F,0x49,0x49,0x49,0x36}},
  {'C', {0x3E,0x41,0x41,0x41,0x22}}, {'D', {0x7F,0x41,0x41,0x22,0x1C}},
  {'E', {0x7F,0x49,0x49,0x49,0x41}}, {'F', {0x7F,0x09,0x09,0x09,0x01}},
  {'G', {0x3E,0x41,0x49,0x49,0x7A}}, {'H', {0x7F,0x08,0x08,0x08,0x7F}},
  {'I', {0x00,0x41,0x7F,0x41,0x00}}, {'J', {0x20,0x40,0x41,0x3F,0x01}},
  {'K', {0x7F,0x08,0x14,0x22,0x41}}, {'L', {0x7F,0x40,0x40,0x40,0x40}},
  {'M', {0x7F,0x02,0x0C,0x02,0x7F}}, {'N', {0x7F,0x04,0x08,0x10,0x7F}},
  {'O', {0x3E,0x41,0x41,0x41,0x3E}}, {'P', {0x7F,0x09,0x09,0x09,0x06}},
  {'Q', {0x3E,0x41,0x51,0x21,0x5E}}, {'R', {0x7F,0x09,0x19,0x29,0x46}},
  {'S', {0x46,0x49,0x49,0x49,0x31}}, {'T', {0x01,0x01,0x7F,0x01,0x01}},
  {'U', {0x3F,0x40,0x40,0x40,0x3F}}, {'V', {0x1F,0x20,0x40,0x20,0x1F}},
  {'W', {0x3F,0x40,0x38,0x40,0x3F}}, {'X', {0x63,0x14,0x08,0x14,0x63}},
  {'Y', {0x07,0x08,0x70,0x08,0x07}}, {'Z', {0x61,0x51,0x49,0x45,0x43}},
};

const uint8_t *glyph(char c) {
  if (c >= 'a' && c <= 'z') c -= 32;
  for (unsigned i = 0; i < sizeof(FONT) / sizeof(FONT[0]); i++)
    if (FONT[i].c == c) return FONT[i].d;
  return FONT[0].d;
}

void setPixel(int x, int y) {
  if (x < 0 || x > 127 || y < 0 || y > 63) return;
  fb[x + (y / 8) * 128] |= (1 << (y & 7));
}

void drawText(int x, int y, const char *s, int scale) {
  for (; *s; s++) {
    const uint8_t *g = glyph(*s);
    for (int col = 0; col < 5; col++)
      for (int row = 0; row < 7; row++)
        if (g[col] & (1 << row))
          for (int dx = 0; dx < scale; dx++)
            for (int dy = 0; dy < scale; dy++)
              setPixel(x + col * scale + dx, y + row * scale + dy);
    x += 6 * scale;
  }
}

void drawBar(int x, int y, int w, int h, int pct) {
  for (int i = 0; i < w; i++) { setPixel(x + i, y); setPixel(x + i, y + h - 1); }
  for (int j = 0; j < h; j++) { setPixel(x, y + j); setPixel(x + w - 1, y + j); }
  int fill = (w - 4) * pct / 100;
  for (int i = 0; i < fill; i++)
    for (int j = 2; j < h - 2; j++) setPixel(x + 2 + i, y + j);
}

// ---------------- application ----------------
bool tankOk = false;
bool tankRaw = false;
unsigned long tankChangeMs = 0;
bool pumpOn = false;
unsigned long pumpStartMs = 0;
unsigned long soakUntilMs = 0;
int moisturePct = 0;
int moistureRaw = 0;

void pump(bool on) {
  if (on && !tankOk) on = false;       // hard interlock: never run with a low tank
  digitalWrite(PIN_PUMP, on ? HIGH : LOW);
  if (on && !pumpOn) pumpStartMs = millis();
  pumpOn = on;
}

int readMoistureRaw() {
  long sum = 0;
  for (int i = 0; i < 16; i++) { sum += analogRead(PIN_SOIL); delay(2); }
  return sum / 16;
}

bool readTankOkRaw() {
  bool closed = (digitalRead(PIN_FLOAT) == LOW);
  return FLOAT_CLOSED_MEANS_OK ? closed : !closed;
}

void setup() {
  pinMode(PIN_PUMP, OUTPUT);
  digitalWrite(PIN_PUMP, LOW);
  pinMode(PIN_FLOAT, INPUT_PULLUP);
  Serial.begin(115200);
  analogReadResolution(12);
  analogSetPinAttenuation(PIN_SOIL, ADC_11db);
  Wire.begin(21, 22);
  Wire.setClock(400000);
  oledInit();
  tankRaw = readTankOkRaw();
  tankOk = false;                      // start with pump blocked until the reading is stable
  tankChangeMs = millis();
}

void loop() {
  unsigned long now = millis();

  // tank: a LOW reading blocks the pump immediately, OK needs to be stable for the debounce time
  bool r = readTankOkRaw();
  if (r != tankRaw) { tankRaw = r; tankChangeMs = now; }
  if (!r) tankOk = false;
  else if (now - tankChangeMs >= TANK_DEBOUNCE_MS) tankOk = true;
  if (!tankOk && pumpOn) pump(false);

  moistureRaw = readMoistureRaw();
  long p = (long)(RAW_DRY - moistureRaw) * 100 / (RAW_DRY - RAW_WET);
  moisturePct = constrain(p, 0, 100);

  if (pumpOn) {
    if (moisturePct >= STOP_ABOVE_PCT || now - pumpStartMs >= PUMP_MAX_MS) {
      pump(false);
      soakUntilMs = now + SOAK_MS;
    }
  } else if (tankOk && moisturePct < START_BELOW_PCT && (long)(now - soakUntilMs) >= 0) {
    pump(true);
  }

  // display
  memset(fb, 0, sizeof(fb));
  char buf[24];
  drawText(0, 0, "SOIL", 2);
  snprintf(buf, sizeof(buf), "%3d%%", moisturePct);
  drawText(128 - 4 * 12, 0, buf, 2);
  drawBar(0, 18, 128, 10, moisturePct);
  drawText(0, 32, "TANK", 2);
  drawText(tankOk ? 128 - 2 * 12 : 128 - 3 * 12, 32, tankOk ? "OK" : "LOW", 2);
  drawText(0, 54, pumpOn ? "PUMP: ON" : "PUMP: OFF", 1);
  if (!tankOk) drawText(64, 54, "REFILL!", 1);
  oledShow();

  static unsigned long lastLog = 0;
  if (now - lastLog > 2000) {
    lastLog = now;
    Serial.printf("raw=%d moisture=%d%% tank=%s pump=%s\n", moistureRaw, moisturePct,
                  tankOk ? "OK" : "LOW", pumpOn ? "ON" : "OFF");
  }
  delay(100);
}
9

Solder resistors and diodes

Fit R1 330 Ohm (gate), R2 10 kOhm (gate pull-down), R3 and R4 5.1 kOhm (USB-C CC pull-downs). Fit D1 1N4007 across the pump terminal with its band to +5 V, and D2 Schottky blocking diode from +5 V to VIN with its band toward VIN. Solder them and trim the leads.

Materials for this step:

Printed Circuit BoardPrinted Circuit Board1 piece
330 Ohm Resistor330 Ohm Resistor1 piece
10K Ohm Resistor10K Ohm Resistor1 piece
Carbon Film ResistorCarbon Film Resistor2 pieces
1N4007 Rectifier Diode1N4007 Rectifier Diode1 piece
Blocking Diode (Schottky)Blocking Diode (Schottky)1 piece
Solder WireSolder Wire1 piece

Tools needed:

Soldering IronSoldering Iron
Flush CuttersFlush Cutters
10

Solder USB-C socket and capacitor

Solder the USB-C receptacle J1 on the left edge, including its shell tabs. Fit the 470 uF 10 V electrolytic capacitor C1 with its minus stripe to GND and solder it.

Materials for this step:

USB-C Receptacle1 piece
Electrolytic CapacitorElectrolytic Capacitor1 piece
Solder WireSolder Wire1 piece

Tools needed:

Soldering IronSoldering Iron
11

Solder MOSFET, sockets and terminals

Solder the IRLZ44N Q1 upright with its tab facing the way shown on the silkscreen. Then solder the two 1x19 female sockets for the ESP32, the 1x4 female socket for the OLED, and the screw terminals J4 (pump), J5 (soil probe) and J6 (float switch). Their openings face the board edge.

Materials for this step:

IRLZ44N Logic-Level MOSFETIRLZ44N Logic-Level MOSFET1 piece
Pin HeaderPin Header3 pieces
Screw Terminal BlockScrew Terminal Block3 pieces
Solder WireSolder Wire1 piece

Tools needed:

Soldering IronSoldering Iron
12

Check the board for shorts

With no modules plugged in, measure the resistance between +5 V and GND, and between 3V3 and GND. Neither should read as a short. Check the polarity of D1, D2 and C1 against the silkscreen.

Tools needed:

MultimeterMultimeter
13

Mount the board in the enclosure

Plug the ESP32 DevKit into the sockets with its antenna end at pin 1, as marked on the board. Plug the OLED into its 4-pin socket after checking that its pin order is GND, VCC, SCL, SDA. Screw the board onto the 5 mm standoffs of the printed enclosure base.

Materials for this step:

ESP32 Development BoardESP32 Development Board1 piece
SSD1306 OLED Display Module1 piece
Self-Tapping ScrewSelf-Tapping Screw4 pieces

Tools needed:

Screwdriver SetScrewdriver Set
14

Flash and calibrate the firmware

Connect the soil probe to J5 (1 = GND, 2 = 3V3, 3 = AOUT), using hookup wire where its leads are too short. Unplug USB-C and connect the ESP32's own USB port to the computer. Upload firmware.ino for the esp32:esp32:esp32 board. In the serial monitor at 115200 baud, note the raw reading with the probe in dry air and again with it in a glass of water up to the line marked on the probe. Enter these as RAW_DRY and RAW_WET, then upload again.

Materials for this step:

Capacitive Soil Moisture Sensor1 piece
Hookup WireHookup Wire1 piece

Tools needed:

Computer with Arduino IDEComputer with Arduino IDE
USB Data Cable
Screwdriver SetScrewdriver Set
Wire StrippersWire Strippers
15

Leak-test the water tank

Fill the printed PETG tank to the brim and stand it on paper towel overnight. If the paper is wet, reprint the tank with more walls and test again.

Tools needed:

Paper TowelPaper Towel
WaterWater
16

Fit the pump, tube and float switch

Cut the silicone tube long enough to reach the pot. Push the silicone tube onto the pump outlet and set the pump on the tank floor under the 12 mm lid hole. Fix the vertical float switch through the 10.5 mm hole in the lid arm tab with its nut, so the float hangs below the tab and drops when the water is low. Lead the tube through the 12 mm hole. Lead the pump and float wires through the cable slot.

Materials for this step:

Water Pump (Submersible)Water Pump (Submersible)1 piece
Float SwitchFloat Switch1 piece
Silicone TubingSilicone Tubing1 m

Tools needed:

Utility KnifeUtility Knife
Screwdriver SetScrewdriver Set
17

Wire the pump, probe and float switch

Stick the enclosure base to the flat lid area beside the holes with double-sided tape. Extend the leads with hookup wire where they are too short, and insulate the joints with heat shrink. Pump to J4 (1 = +5 V, the red pump wire; 2 = drain). Float switch to J6. Bring the wires in through the slot in the side wall, then push the enclosure lid on.

Materials for this step:

Double-Sided TapeDouble-Sided Tape1 piece
Hookup WireHookup Wire1 piece
Heat Shrink TubingHeat Shrink Tubing1 piece
Solder WireSolder Wire1 piece

Tools needed:

Wire StrippersWire Strippers
Soldering IronSoldering Iron
Heat GunHeat Gun
Screwdriver SetScrewdriver Set
18

Place the probe and drip stake

Push the soil probe into the pot up to its marked line, keeping the electronics end dry. Push the tube onto the drip stake spigot and push the stake into the soil. Set the tank lower than the pot so that the full water line sits below the soil surface. Otherwise water can siphon from the tank into the pot after the pump stops.

Tools needed:

Flower PotFlower Pot
19

Power up and test

Fill the tank and plug in the USB-C adapter and cable. Check the OLED shows soil % and tank OK. Lift the probe into air: the pump should run for at most 5 s and then wait 60 s. Empty the tank until the float drops: the display should show LOW and the pump must not run. Measure the 5 V rail while the pump runs and check that it stays above about 4.5 V.

Materials for this step:

USB-C Power Adapter1 piece
USB-C Cable1 piece

Tools needed:

MultimeterMultimeter
WaterWater
20

How this product was generated

AI Generated with Prompt to Product

Materials

24

Tools Required

12

Design Files

5
  • cus_ai_ed_electronics_01-pcb-prodjob_01M7JF9J0992HT4DPFFBR6HWMQ-pcb-1-4ae5c860.stlSTLCC0
    69.0 KB
  • cus_ai_ed_electronics_01-pcb-prodjob_01M7JF9J0992HT4DPFFBR6HWMQ-pcb-2-bba1cabe.stlSTLCC0
    3.2 KB
  • cus_ai_ed_electronics_01-product-prodjob_01M7JF9J0992HT4DPFFBR6HWMQ-1-bf47bc6c.stlSTLCC0
    1.4 KB
  • cus_ai_ed_electronics_01-product-prodjob_01M7JF9J0992HT4DPFFBR6HWMQ-2-e11cea1f.stlSTLCC0
    30.8 KB
  • cus_ai_ed_electronics_01-product-prodjob_01M7JF9J0992HT4DPFFBR6HWMQ-3-bea0de92.stlSTLCC0
    53.3 KB

CC0 Public Domain

This blueprint is released under CC0. You are free to copy, modify, distribute, and use this work for any purpose, without asking permission.

Support the Maker by purchasing products through their Blueprint where they earn a Maker Commission set by Vendors, or create a new iteration of this Blueprint and include it as a connection in your own Blueprint to share revenue.

Discussion

(0)

Log in to join the discussion

Loading comments...