Collaboration
ART
BEAUTY & WELLNESS
CRAFT
CULTURE & HISTORY
ENTERTAINMENT
ENVIRONMENT
FOOD & DRINKS
REVERSE ENGINEERING
SCIENCES
SPORTS
TECHNOLOGY
WEARABLES
Double-Ended Scriber from a Worn Saw File: Annealed in Lime, Filed Round in a Grooved Block, Points Hardened (Thompson, Amateur Work)
Forge

Created by

Forge

14. November 2026NO
8
0
0
0
0

Double-Ended Scriber from a Worn Saw File: Annealed in Lime, Filed Round in a Grooved Block, Points Hardened (Thompson, Amateur Work)

The marking scriber Richard Thompson made for his surface gauge in Amateur Work: 1/8 in. steel or a worn-out saw file, drilled in the middle, pointed at both ends with one end bent, annealed by burying it red-hot in lime, filed round while turned in a grooved hardwood block, and the points hardened.
Beginner
Two hours

Instructions

1

Read Thompson

"A worn-out saw file will answer very well, with a hole drilled through the centre to fit the bolt and pointed at each end, one of which is bent."
2

Rough the shape

Forge a flat piece of steel about 1/8 in. (3 mm) thick, or a worn-out saw file, roughly to shape: pointed at both ends, one end bent into a short hook (his fig. 30).

Materials for this step:

Tool Steel Flat BarTool Steel Flat Bar1 piece

Tools needed:

Blacksmith ForgeBlacksmith Forge
AnvilAnvil
HammerHammer
Blacksmith TongsBlacksmith Tongs
3

Anneal in lime

Heat it gently to a dull red and bury it in lime to cool slowly: it is then easy to file.

Materials for this step:

Lime (Calcium Hydroxide)Lime (Calcium Hydroxide)1 piece

Tools needed:

Blacksmith ForgeBlacksmith Forge
Blacksmith TongsBlacksmith Tongs
4

Drill and flatten

Drill a hole through the middle to fit the mounting bolt and file the flat part to an even thickness for about 1/2 in. each side of the hole.

Tools needed:

Drill PressDrill Press
Bench ViseBench Vise
Files (Hand File)Files (Hand File)
5

File it round

Cut a groove along the end of a hardwood block about 3 x 2 x 1/2 in., held end up in the vice. Lay the scriber in the groove, turn it slowly toward you with the left hand and file it round with the right. File the points quite sharp.

Materials for this step:

Hardwood BoardHardwood Board1 piece

Tools needed:

Hand SawHand Saw
Bench ViseBench Vise
Files (Hand File)Files (Hand File)
6

Harden the points

Harden the points (he gives no method; ours: heat the tips to a bright red and quench in water), then touch them up on an oilstone.

Tools needed:

Blacksmith ForgeBlacksmith Forge
Quench BucketQuench Bucket
WhetstoneWhetstone
7

Troubleshooting

Scriber troubleshooting.

Flow

Loading...
8

History and honest limits

From Richard Thompson, "How to Construct a Compound Microscope" III, **Amateur Work, Illustrated**, vol. III, p. 198 and fig. 30 (checked on the archive.org scan amateurworkillus03lond). He mounts the scriber on a mahogany surface gauge with three brass washers 3/4 in. across and 1/16 in. thick. The hardening method, metric figures and tools are ours.

Materials

3

Tools Required

10

This blueprint makes

Related Blueprints

These blueprints share knowledge with this one — techniques, materials, or principles that connect them in the learning graph.

CC0 Public Domain

This blueprint is released under CC0. You are free to copy, modify, distribute, and use this work for any purpose, without asking permission.

Support the Maker by purchasing products through their Blueprint where they earn a Maker Commission set by Vendors, or create a new iteration of this Blueprint and include it as a connection in your own Blueprint to share revenue.

Discussion

(0)

Log in to join the discussion

Loading comments...