NGHỆ THUẬT
LÀM ĐẸP VÀ SỨC KHỎE
THỦ CÔNG
VĂN HÓA VÀ LỊCH SỬ
GIẢI TRÍ
MÔI TRƯỜNG
THỰC PHẨM VÀ ĐỒ UỐNG
KỸ THUẬT NGƯỢC
KHOA HỌC
THỂ THAO
CÔNG NGHỆ
THIẾT BỊ ĐEO

Cooking Thermometer: Candy Thermometer in a Glass Tube with a Venting Plastic Cap (Chaney, US 3,636,769, 1972)
A candy and deep-fat thermometer that clips to the side of a pan. A glass thermometer on a printed scale card sits inside a protective glass tube, so it never touches the candy. The top of the tube is closed by a polyethylene cap that seals in normal use but softens when the whole thermometer is heated far too hot, as in an oven, so the air inside escapes instead of bursting the tube.
Result: a pan-side cooking thermometer that cannot explode if overheated.
Source: J. L. Chaney, US 3,636,769 (1972). Unknown: the scale range, sizes and several materials. Picture: the patent drawing.
Trung cấp
Unknown
Hướng dẫn
1
1
Mount the thermometer on its scale
Mount the thermometer on its scale
Fasten a glass thermometer tube to a graduated scale card with small fasteners, the bulb at the bottom. The patent's card is marked with cooking points such as soft ball, hard ball, soft crack, hard crack, fish, fowl, potatoes and doughnuts. Fix a disk on top of the card to keep it centred in the outer tube. Not given: the range, the card and fastener materials.
Vật liệu cho bước này:
Nhiệt kế phòng thí nghiệm1 thermometer tube
Vật liệu không rõ1 scale card, disk
Kim loại chưa rõ1 fastenersCông cụ cần thiết:
Kích thước chưa rõ2
2
Enclose it in the protective tube
Enclose it in the protective tube
Slide the card and thermometer into a glass protective tube, open at the top, so the bulb reaches the lower end and touches a metal cap there to pass on the heat. Not given: the tube size, the metal of the end cap, how the cap is joined to the tube.
Vật liệu cho bước này:
Ống thủy tinh1 protective tube
Kim loại chưa rõ1 end capCông cụ cần thiết:
Kích thước chưa rõ3
3
Fit the venting cap
Fit the venting cap
Close the open top with a cup-shaped cap of a thermoplastic such as polyethylene, a friction fit that seals out dirt. Polyethylene softens at about 180 °F and melts near 250 °F: if the thermometer is heated in an oven to 400-550 °F, the air inside would reach 12-14 psi, but the cap distorts first and lets it out. Do not use rubber or a thermosetting plastic, which does not vent. Ours: LDPE.
Vật liệu cho bước này:
Hạt nhựa LDPE1 capCông cụ cần thiết:
Kích thước chưa rõ4
4
Fit the pan clip and use it
Fit the pan clip and use it
Slide a spring clip onto the outside of the tube; its spring arm holds the thermometer upright over the edge of the pan. Clip it on with the bulb end in the candy or fat and read the scale; it also serves for deep frying. Ours: spring steel wire.
Vật liệu cho bước này:
Dây thép lò xo1 clipCông cụ cần thiết:
Kìm mỏ trònVật liệu
6- 1 thermometer tubeTạm thời
- 1 scale card, diskTạm thời
- 1 end capTạm thời
- 1 protective tubeTạm thời
- 1 capTạm thời
- 1 clipTạm thời
Công cụ yêu cầu
2- Tạm thời
- Tạm thời
Vật liệu bản thiết kế liên kết

Nguy hiểm
Phân bổ 10%
Liquid-in-Glass Thermometer: Bulb, Fill, Seal and Scale
bởi Penny
Gia công thủy tinh
38
0
0
0
1
0

Nguy hiểm
Phân bổ 10%
LDPE Pellets: Ethylene Polymerised at 1500 Atmospheres with a Trace of Oxygen
bởi Charlie
Công nghiệp
9
0
0
0
2
0

Phân bổ 10%
Spring Steel Strip and Wire, Hardened and Tempered
bởi Forge
Gia công kim loại
45
0
0
0
4
0
Bản thiết kế này làm ra
CC0 Phạm vi công cộng
Bản thiết kế này được phát hành theo CC0. Bạn tự do sao chép, sửa đổi, phân phối và sử dụng cho bất kỳ mục đích nào mà không cần xin phép.
Hỗ trợ nhà sáng tạo bằng cách mua sản phẩm qua bản thiết kế, nơi họ nhận Hoa hồng nhà sáng tạo do nhà bán hàng đặt, hoặc tạo phiên bản mới và kết nối trong bản thiết kế riêng để chia sẻ doanh thu.
