NGHỆ THUẬT
LÀM ĐẸP VÀ SỨC KHỎE
THỦ CÔNG
VĂN HÓA VÀ LỊCH SỬ
GIẢI TRÍ
MÔI TRƯỜNG
THỰC PHẨM VÀ ĐỒ UỐNG
KỸ THUẬT NGƯỢC
KHOA HỌC
THỂ THAO
CÔNG NGHỆ
THIẾT BỊ ĐEO

Building a Langspil — The Icelandic Drone Zither
Build Iceland's traditional drone zither: a long wooden soundbox with one fretted melody string and two drone strings that ring constantly beneath the tune, so a single player makes melody and harmony at once. A serious maker build in the drone zither and how a soundbox amplifies strings.
Trung cấp
Several hours over a few sessions
Hướng dẫn
1
1
Melody and drone from one box
Melody and drone from one box
The langspil is Iceland's drone zither: a long soundbox with one fretted melody string and one or two drone strings that ring under every note, so one player sounds a tune AND its harmony at once.
2
2
Cut the soundbox parts
Cut the soundbox parts
Cut a base, two side ribs and two end blocks for a long, narrow box about 80 cm long and 8-10 cm wide. Icelanders used driftwood — pine, birch or oak.
Vật liệu cho bước này:
Baltic Birch Plywood (1/8 inch, 12x12, 10-Pack)1 cáiCông cụ cần thiết:
Hacksaw3
3
Glue the box frame
Glue the box frame
Glue the two ribs to the base and end blocks to make a long, shallow open box. Clamp it and let the glue set fully.
Vật liệu cho bước này:
PVA Wood Glue1 cái4
4
Fit the soundboard
Fit the soundboard
Glue a thin softwood soundboard over the top, overlapping the ribs slightly, to seal a resonant chamber. A thin, light top vibrates best.
Vật liệu cho bước này:
Dry Softwood Board1 cái
PVA Wood Glue1 cái5
5
Cut a soundhole
Cut a soundhole
Cut a round soundhole in the soundboard so the sound built up inside the box can escape.
Công cụ cần thiết:
Sloyd Carving Knife6
6
Drill the peg holes
Drill the peg holes
At the headstock end, bore three tapered holes through the top for the tuning pegs — one for the melody string, two for the drones.
Công cụ cần thiết:
Awl7
7
Fit the tuning pegs
Fit the tuning pegs
Push a friction tuning peg into each hole so it turns stiffly and holds string tension without slipping.
Vật liệu cho bước này:
Tuning Pegs3 cái8
8
Carve the nut and bridge
Carve the nut and bridge
Carve a small hardwood nut near the pegs and a low bridge near the far end. The strings ride over both, lifted clear of the soundboard.
Công cụ cần thiết:
Sloyd Carving Knife9
9
String it
String it
Anchor three steel strings to small pins at the far end, run them over the bridge and nut, and wind each onto its tuning peg.
Vật liệu cho bước này:
Steel Music Wire1 cái10
10
Set the frets
Set the frets
Fit small metal frets across the soundboard UNDER THE MELODY STRING ONLY, spaced so pressing behind each one gives the next note of a diatonic scale.
Vật liệu cho bước này:
Fret Wire1 cáiCông cụ cần thiết:
Metal File11
11
Tune the drones
Tune the drones
Tune the two drone strings to a low keynote and its octave or fifth. They will sound continuously, giving the langspil its droning voice.
12
12
Tune the melody string
Tune the melody string
Tune the melody string to the keynote too. Check it against the frets — pressing behind each fret should climb cleanly through the scale.
13
13
Play it
Play it
Press the melody string behind the frets with one hand and pluck it with the other. The drones ring under every note. Try bowing or gently hammering it too.
14
14
Compendium — the drone zither
Compendium — the drone zither
The langspil is a drone zither: a resonant box with strings stretched along the top. One fretted MELODY string carries the tune while one or two DRONE strings hold a constant note, so a single player produces melody and harmony together — the same principle as a bagpipe's chanter over its drones, or a hurdy-gurdy. The sealed soundbox is a resonator: the thin strings alone move almost no air, but they shake the light soundboard, which drives the air inside the box, which spills out through the soundhole — the box amplifies the strings, exactly as in a guitar or violin. String pitch follows the same three rules as the musical bow — tension, length and mass — and pressing the melody string just behind a fret shortens its speaking length to raise the pitch by a fixed step, which is the whole point of the frets. Iceland has few trees, so langspils were built from driftwood — pine, birch, oak; the instrument is first recorded in the 18th century and is a northern cousin of the German scheitholt and the Appalachian dulcimer, all box drone zithers. Icelandic schoolchildren still build and play their own today, some laser-cut from plywood in a Fab Lab — a heritage instrument kept alive by making it.
Vật liệu
6- Tạm thời
- 2 cáiTạm thời
- 1 cáiTạm thời
- 3 cáiTạm thời
- Tạm thời
Blueprint liên quan
Các blueprint này chia sẻ kiến thức — kỹ thuật, vật liệu hoặc nguyên tắc
Related blueprints
Other builds that share materials, tools, or techniques with this one.

Building a Janggu — The Korean Hourglass Drum

Building a Đàn Bầu — Vietnam's One-String Harmonic Zither

Building a Roman Ballista — The Torsion-Powered Bolt Throwerengineering

Building an Arab Kamal — The Indian Ocean Navigator's Latitude FinderPhysics & Astronomy

Building a Persian Windmill — The First Machine Powered by Windengineering

Building a Roman Odometer — The Gear-Driven Distance Measurerengineering
CC0 Phạm vi công cộng
Bản thiết kế này được phát hành theo CC0. Bạn tự do sao chép, sửa đổi, phân phối và sử dụng cho bất kỳ mục đích nào mà không cần xin phép.
Hỗ trợ nhà sáng tạo bằng cách mua sản phẩm qua bản thiết kế, nơi họ nhận Hoa hồng nhà sáng tạo do nhà bán hàng đặt, hoặc tạo phiên bản mới và kết nối trong bản thiết kế riêng để chia sẻ doanh thu.