NGHỆ THUẬT
LÀM ĐẸP VÀ SỨC KHỎE
THỦ CÔNG
VĂN HÓA VÀ LỊCH SỬ
GIẢI TRÍ
MÔI TRƯỜNG
THỰC PHẨM VÀ ĐỒ UỐNG
TƯƠNG LAI XANH
KỸ THUẬT NGƯỢC
KHOA HỌC
THỂ THAO
CÔNG NGHỆ
THIẾT BỊ ĐEO
Nalbinding a Wool Sock in the Oslo Stitch — The Looped Fabric Before Knitting
Long before knitting, people made warm, hard-wearing socks and mittens by nalbinding — looping short lengths of wool with a single flat needle. Unlike knitting, which pulls loops through loops with two rods and can unravel, nalbinding passes the whole working thread through each stitch, giving a dense, felt-firm fabric that will not run. This blueprint works the simple Oslo stitch into a tube for a sock or mitten, joining new wool with a felted splice rather than a knot — exactly as the Vikings did.
Trung cấp
4
Hướng dẫn
1
1
Cut a short working length
Cut a short working length
Cut about an arm's length of wool yarn — not a whole ball. In nalbinding the entire length is pulled through every stitch, so you work with short pieces and splice on more as needed.
Vật liệu cho bước này:
Wool Yarn Skein (Undyed)1 cáiCông cụ cần thiết:
Sharp Scissors2
2
Thread the flat needle
Thread the flat needle
Thread the yarn through the eye of the flat nalbinding needle. The needle is broad, blunt and eyed at one end — bone, antler or wood — and never has a hook.
Công cụ cần thiết:
Nalbinding Needle3
3
Make the foundation loops
Make the foundation loops
Loop the yarn around your thumb and make a short chain of starting loops. These foundation loops are the base row that every following stitch will anchor into.
Công cụ cần thiết:
Nalbinding Needle4
4
Work the Oslo stitch
Work the Oslo stitch
Pass the needle under the thumb loop and up through the working loop to form the Oslo stitch — the simplest nalbinding stitch. Draw each stitch snug and even, building the first row.
Công cụ cần thiết:
Nalbinding Needle5
5
Join into a round
Join into a round
For a sock or mitten, connect the ends of the first row into a ring by stitching the last stitch into the first, so you can then work round and round to form a tube.
Công cụ cần thiết:
Nalbinding Needle6
6
Work in a spiral
Work in a spiral
Continue in a spiral, anchoring each new Oslo stitch into the loop of the row below. Keep the tension steady so the tube grows even in width — this becomes the leg of the sock.
Công cụ cần thiết:
Nalbinding Needle7
7
Splice in new yarn
Splice in new yarn
When the length runs short, join a new piece with a felted splice, not a knot: untwist and overlap the two wool ends, wet them, and roll them briskly between your palms until the fibres felt into one continuous thread.
Vật liệu cho bước này:
Wool Yarn Skein (Undyed)1 cáiCông cụ cần thiết:
Nalbinding Needle8
8
Shape the tube
Shape the tube
Increase by working two stitches into one loop and decrease by skipping a loop, shaping the tube — narrowing for an ankle, turning a heel, or rounding a mitten — as the piece requires.
Công cụ cần thiết:
Nalbinding Needle9
9
Close the toe
Close the toe
At the end, decrease steadily until only a few loops remain, then pass the needle through them and draw them tight to close the toe or mitten tip.
Công cụ cần thiết:
Nalbinding Needle10
10
Secure and trim the tail
Secure and trim the tail
Weave the final yarn tail back through several stitches on the inside to lock it, then trim it flush. Because the fabric is looped, not knitted, it cannot unravel from the cut end.
Công cụ cần thiết:
Nalbinding NeedleSharp ScissorsVật liệu bản thiết kế liên kết
Blueprint liên quan
Các blueprint này chia sẻ kiến thức — kỹ thuật, vật liệu hoặc nguyên tắc
Related blueprints
Other builds that share materials, tools, or techniques with this one.
Nålbinding with the Oslo Stitch — Looped Fabric from a Single Needletextiles
Mulching — Covering the Soil to Save Water and Feed It
Alloying Bronze (Cu + Sn) — The Bronze Age Beginsmaterials/metals
Building a Song Dynasty Fire Lance — The World's First Gunpowder Weaponchemistry
Casting a Pewter Spoon in a Soapstone Mould — Low-Temperature Metal CastingMetalworking
Waterproofing a Basket with Pine Pitch — Sealed Container for Liquidswoodworking
CC0 Phạm vi công cộng
Bản thiết kế này được phát hành theo CC0. Bạn tự do sao chép, sửa đổi, phân phối và sử dụng cho bất kỳ mục đích nào mà không cần xin phép.
Hỗ trợ nhà sáng tạo bằng cách mua sản phẩm qua bản thiết kế, nơi họ nhận Hoa hồng nhà sáng tạo do nhà bán hàng đặt, hoặc tạo phiên bản mới và kết nối trong bản thiết kế riêng để chia sẻ doanh thu.