NGHỆ THUẬT
LÀM ĐẸP VÀ SỨC KHỎE
THỦ CÔNG
VĂN HÓA VÀ LỊCH SỬ
GIẢI TRÍ
MÔI TRƯỜNG
THỰC PHẨM VÀ ĐỒ UỐNG
KỸ THUẬT NGƯỢC
KHOA HỌC
THỂ THAO
CÔNG NGHỆ
THIẾT BỊ ĐEO
Propane Hand Torch: Goss, 1949
Emma

Tạo bởi

Emma

12. tháng Mười 2026SE
10
0
0
0
0

Propane Hand Torch: Goss, 1949

John C. Goss of Pittsburgh patented this hand torch, US 2,465,643, in March 1949. It burns propane, which turns from liquid to gas so readily that, shut in a tank, it makes its own working pressure: unlike the older blow torch, it needs no pump. The knurled cylindrical tank is also the handle. A dispersion tube hangs from the tank top to about half the tank's height and draws gas, not liquid, through a minute port in its end cap. A needle valve meters the gas to a nozzle bent back at about thirty degrees to the tank. A spring-loaded ball check valve lets the tank be filled from a supply bottle but lets nothing out.
Nâng cao
Workshop process

Hướng dẫn

1

Tank

Make an elongated, gas-tight cylindrical metal tank with a bottom and a top. Knurl rows of bands round the outside: the tank is also the handle.

Vật liệu cho bước này:

Bình nhiên liệu đèn khò có khíaBình nhiên liệu đèn khò có khía1 cái

Công cụ cần thiết:

Máy tiện kim loạiMáy tiện kim loại
Dụng cụ cán nhámDụng cụ cán nhám
2

Top with bosses

Form the tank top with a valve boss and a nozzle boss integral with it. The valve boss holds a chamber divided by a valve seat; a channel joins the chamber above the seat to the bore of the nozzle boss.

Vật liệu cho bước này:

Nắp bình đèn khò có bệ van và bệ vòi phunNắp bình đèn khò có bệ van và bệ vòi phun1 cái
3

Dispersion tube

Fix a dispersion tube in the top, near the centre, reaching down to about half the tank's height. Its upper end opens into the valve chamber below the seat; its lower end carries a fixed cap with a minute inlet port.

Vật liệu cho bước này:

Ống phân tán có nắp đầu vàoỐng phân tán có nắp đầu vào1 cái
4

Valves and nozzle

Screw the needle control valve into the valve boss through a packing gland and nut, and fit the adjusting cap. Fix the nozzle pipe on the nozzle boss with a crown nut, angled back about thirty degrees to the tank. Mount the spring-loaded ball check valve in its casing in the top and close it with the sealing plug.

Vật liệu cho bước này:

Van kim điều chỉnhVan kim điều chỉnh1 cái
Vòi phun đèn khò và ống vòi phunVòi phun đèn khò và ống vòi phun1 cái
Van một chiều biVan một chiều bi1 cái

Công cụ cần thiết:

Mỏ lếtMỏ lết
5

Charge with propane

Remove the sealing plug and connect the supply bottle: liquid propane flows in through the check valve. Fill to no more than half the tank. With the control valve open while charging, liquid spitting from the nozzle shows the level has reached the dispersion tube's end. Replace the plug.

Vật liệu cho bước này:

PropanPropan1 as required

Công cụ cần thiết:

Mỏ lếtMỏ lết

Vật liệu

7

Công cụ yêu cầu

3

Bản thiết kế này làm ra

Blueprint liên quan

Các blueprint này chia sẻ kiến thức — kỹ thuật, vật liệu hoặc nguyên tắc

CC0 Phạm vi công cộng

Bản thiết kế này được phát hành theo CC0. Bạn tự do sao chép, sửa đổi, phân phối và sử dụng cho bất kỳ mục đích nào mà không cần xin phép.

Hỗ trợ nhà sáng tạo bằng cách mua sản phẩm qua bản thiết kế, nơi họ nhận Hoa hồng nhà sáng tạo do nhà bán hàng đặt, hoặc tạo phiên bản mới và kết nối trong bản thiết kế riêng để chia sẻ doanh thu.

Thảo luận

(0)

Đăng nhập để tham gia thảo luận

Đang tải bình luận...