NGHỆ THUẬT
LÀM ĐẸP VÀ SỨC KHỎE
THỦ CÔNG
VĂN HÓA VÀ LỊCH SỬ
GIẢI TRÍ
MÔI TRƯỜNG
THỰC PHẨM VÀ ĐỒ UỐNG
KỸ THUẬT NGƯỢC
KHOA HỌC
THỂ THAO
CÔNG NGHỆ
THIẾT BỊ ĐEO
Bevel Protractor
Mark

Tạo bởi

Mark

2. tháng Tám 2026FI
1
0
0
0
0

Bevel Protractor

Length has an obvious standard: a bar you can copy. Angle has none — you cannot keep a master 37° in a drawer. Angle must be divided out of the circle every time, which makes it the harder measurement.

US 165,519, “Protractor”, Ambrose Swasey of Hartford, Connecticut, granted 13 July 1875 — an instrument for draughtsmen, machinists and surveyors. Swasey's bevel protractor puts a vernier on a rotating blade, so the reading goes below the whole degree to minutes of arc.

Swasey was 29 and working at Pratt & Whitney. He later co-founded Warner & Swasey and built the mountings for some of the largest telescopes in the world — the same problem of dividing a circle precisely, at a very different scale.

Cơ bản
45 minutes

Hướng dẫn

1

Read the claim before you build

Swasey claims a vernier on a rotating blade. Write down why an angle cannot be stored as a physical master the way a length can.

2

Measure an angle with a plain protractor

Draw any angle on graph paper and read it with the plain protractor. Record your best estimate and how confident you are in the last digit.

Vật liệu cho bước này:

Graph PaperGraph Paper1 tờ

Công cụ cần thiết:

ProtractorProtractor
3

Have someone else read the same angle

Ask another person to read your angle. Compare. The disagreement is the problem Swasey is solving.

Công cụ cần thiết:

ProtractorProtractor
4

Understand the vernier principle

A vernier scale has divisions slightly SMALLER than the main scale. Whichever pair of lines coincides tells you the fraction. Write that sentence out.

Vật liệu cho bước này:

Graph PaperGraph Paper1 tờ
5

Find the coincidence on a real vernier

Open the vernier caliper to an arbitrary width. Find the one vernier line that aligns with a main line. That single alignment is the extra digit.

Công cụ cần thiết:

Vernier CaliperVernier Caliper
Magnifying GlassMagnifying Glass
6

Draw a 12-division main scale

On graph paper draw 12 divisions at exactly 10 mm each along a line.

Vật liệu cho bước này:

Graph PaperGraph Paper1 tờ

Công cụ cần thiết:

Steel Ruler (30cm)Steel Ruler (30cm)
7

Draw a 10-division vernier

On a separate strip draw 10 divisions at 9 mm each. Cut it out. Ten of yours span nine of theirs.

Vật liệu cho bước này:

Graph PaperGraph Paper1 tờ

Công cụ cần thiết:

Steel Ruler (30cm)Steel Ruler (30cm)
Sharp ScissorsSharp Scissors
8

Read tenths with your paper vernier

Slide the strip along the main scale. Whichever line coincides gives the tenth. You have added a digit with no finer engraving.

9

Build the rotating blade

Cut a card blade 150 mm long, pin it through a card disc at the centre with a screw so it swings freely.

Vật liệu cho bước này:

Graph PaperGraph Paper1 tờ
#6-32 Machine Screw#6-32 Machine Screw1 cái

Công cụ cần thiết:

Sharp ScissorsSharp Scissors
10

Graduate the disc

Mark the disc every 5° using the protractor as the master. Every instrument is copied from a better one; the chain has to stop somewhere.

Công cụ cần thiết:

ProtractorProtractor
Permanent MarkerPermanent Marker
11

Add the vernier arc

Glue your 10-division strip, curved, to the blade so it rides against the disc graduations.

Vật liệu cho bước này:

Wood GlueWood Glue2 ml
12

Measure a real corner

Set the blade against a corner of the wooden board and read degrees plus vernier fraction.

Vật liệu cho bước này:

Flat Wooden BoardFlat Wooden Board1 cái
13

Check against a known right angle

Read a corner you believe is 90°. Any deviation is either the corner or your instrument — reverse the tool to find out which, as in the level blueprint.

Công cụ cần thiết:

Steel Ruler (30cm)Steel Ruler (30cm)
14

History & Context

US 165,519, “Protractor”, Ambrose Swasey, Hartford, Connecticut, granted 13 July 1875.

Swasey was born on a New Hampshire farm in 1846 and was working at Pratt & Whitney when this issued. In 1880 he and Worcester Warner founded Warner & Swasey in Cleveland, which built turret lathes — and the mountings and telescopes for Lick, Yerkes and other great observatories. Dividing a circle accurately is the same problem whether the circle is 100 mm across on a machinist's bench or a telescope's setting circle tracking a star.

Why angle is genuinely harder than length. You can keep a metre bar in a vault and compare copies to it. You cannot keep an angle: an angle is a ratio, and the only physical master is a divided circle, which someone had to divide in the first place. Historically that was the dividing engine, and the accuracy of every protractor traces back to one.

The vernier's elegance. It adds a decimal digit using nothing but two scales of slightly different pitch — no gears, no optics, no power. Pierre Vernier published it in 1631. That a 1631 idea is still the readout on a 1875 patent, and on the caliper in step 5, says something about how rarely a genuinely good idea needs replacing.

Vật liệu

4

Công cụ yêu cầu

6

Vật liệu bản thiết kế liên kết

Blueprint liên quan

Các blueprint này chia sẻ kiến thức — kỹ thuật, vật liệu hoặc nguyên tắc

CC0 Phạm vi công cộng

Bản thiết kế này được phát hành theo CC0. Bạn tự do sao chép, sửa đổi, phân phối và sử dụng cho bất kỳ mục đích nào mà không cần xin phép.

Hỗ trợ nhà sáng tạo bằng cách mua sản phẩm qua bản thiết kế, nơi họ nhận Hoa hồng nhà sáng tạo do nhà bán hàng đặt, hoặc tạo phiên bản mới và kết nối trong bản thiết kế riêng để chia sẻ doanh thu.

Thảo luận

(0)

Đăng nhập để tham gia thảo luận

Đang tải bình luận...